基于减容增效的超低比转速轴流式叶片水力设计

中国机械工程 ›› 2012, Vol. 23 ›› Issue (3): 320-323.

基于减容增效的超低比转速轴流式叶片水力设计

刘有余1,2;韩江2

1. 安徽工程大学,芜湖,241000

2.合肥工业大学,合肥,230009

出版日期:2012-02-10 发布日期:2012-02-15
基金资助:
国家自然科学基金资助项目（51175001）；安徽省高等学校省级自然科学研究项目（KJ2011B023）；安徽省自然科学基金资助项目（11040606M144）
National Natural Science Foundation of China（No. 51175001）;

Anhui Provincial Natural Science Program of Higher Education of China（No. KJ2011B023）;
Anhui Provincial Natural Science Foundation of China（No. 11040606M144）

Hydraulic Design of Axial Turbine Blades with Ultra-low Specific Speed for Decreasing Capacity and Increasing Efficiency

Liu Youyu1, 2;Han Jiang2

1.Anhui Polytechnic University,Wuhu, Anhui, 241000

2.Hefei University of Technology, Hefei,230009

Online:2012-02-10 Published:2012-02-15
Supported by:

National Natural Science Foundation of China（No. 51175001）;

Anhui Provincial Natural Science Program of Higher Education of China

（No. KJ2011B023）;
Anhui Provincial Natural Science Foundation of China（No. 11040606M144）

摘要/Abstract

摘要：

为解决轴流定桨式机组枯水期小流量下不能发电的难题,在分析其原因的基础上提出减容增效实施策略;研究了进出口轴向流速及环量沿半径分布规律;解决了计算机辅助水力设计关键技术难题,包括翼型展开图向计算流面圆柱面转化技术及曲线智能延伸技术;用自行开发的CAD软件为一实际机组设计轴流式叶片,在流量从4.5m3/s减至1.5m3/s时,机组效率从改造前的低于30.1%增大至82.7%,机组能够正常发电,且叶片汽蚀性能优于原转轮汽蚀性能。



关键词:

轴流式叶片, 减容增效, 超低比转速, 计算机辅助水力设计

Abstract:

To solve the problem that propeller turbines were unfit for working under small discharge conditions in dry seasons, after discussing the influencing factors, a rebuilding scheme for decreasing capacity and increasing efficiency was put forward. The distribution of the axial velocity and the velocity circulation at the inlet and the outlet were researched. Some key technologies in computer aided hydraulic design were solved herein, including unfolded drawing of aero foil converted to cylindrical surface and intelligent extension of curve. An example of a runner blade for a real turbine sets was successfully developed with the self-development CAD software. When the discharge is decreased from 4.5m3/s to 1.5m3/s, the efficiency of the hydraulic turbine increases from less than 30.1% to 82.7%, then the sets can work properly, and its cavitation performances are superior to the original one.

Key words: axial turbine blade, decreasing capacity &, increasing efficiency, ultra-low specific speed, computer aided hydraulic design

中图分类号:

刘有余1, 2, 韩江2.

基于减容增效的超低比转速轴流式叶片水力设计

[J]. 中国机械工程, 2012, 23(3): 320-323.

LIU Wei-Tu-1, 2, HAN Jiang-2.

Hydraulic Design of Axial Turbine Blades with Ultra-low Specific Speed for Decreasing Capacity and Increasing Efficiency

[J]. China Mechanical Engineering, 2012, 23(3): 320-323.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/

http://www.cmemo.org.cn/CN/Y2012/V23/I3/320

[1]	王国彪, 赖一楠, 范大鹏, 杨华勇, 王时龙. 新型精密传动机构设计与制造综述 [J]. J4, 201016, 21(16): 1891-1897.
[2]	王立存, 陈进, 张贤明, 陈国强. 基于泛函的制冷涡旋压缩机变壁厚涡旋型线理论及形状优化 [J]. J4, 201016, 21(16): 1898-1901.
[3]	李小力, 陈威, 闫蓉. 基于BP神经网络的空间轮廓误差自适应补偿 [J]. J4, 201016, 21(16): 1902-1906.
[4]	夏瑞雪, 卢荣胜, 刘宁, 董敬涛. 基于圆点阵列靶标的特征点坐标自动提取方法 [J]. J4, 201016, 21(16): 1906-1910.
[5]	陈立锋, 吴晓铃, 秦大同, 肖正明. 齿轮啮合过程摩擦功耗研究 [J]. J4, 201016, 21(16): 1911-1915.
[6]	李明磊, 贾育秦, 张学良, 刘丽琴, 杜娟, 温淑花, 兰国生. 基于多目标差异演化算法的并联机构结构优化 [J]. J4, 201016, 21(16): 1915-1920.
[7]	吴怀超, 吴白羽, 张秀华. 石蜡感温阀传热性能的数字仿真研究 [J]. J4, 201016, 21(16): 1921-1926.
[8]	鲁开讲, 师俊平, 张锋涛. 平面三自由度并联机构动力学优化设计 [J]. J4, 201016, 21(16): 1926-1931.
[9]	张敏杰, 王庆九, 管成. 并联式油液混合动力挖掘机动力系统仿真研究 [J]. J4, 201016, 21(16): 1932-1936.
[10]	刘安平, 刘济春. IPC-208B型原子力显微镜大范围扫描三维驱动系统研究 [J]. J4, 201016, 21(16): 1936-1940.
[11]	姚运萍, 王智渊. 螺栓连接受载能量损失与结合面参数识别 [J]. J4, 201016, 21(16): 1941-1943,1951.
[12]	陈建, 邓利娟. 恒力弹性机构的设计 [J]. J4, 201016, 21(16): 1944-1946.
[13]	罗洁思, 于德介, 史美丽. 基于SVD和线调频小波路径追踪的转速波动齿轮箱故障诊断 [J]. J4, 201016, 21(16): 1947-1951.
[14]	战晓磊, 辛洪兵, 汉斯·彼德　兰特斯. 基于虚拟现实的MOTOMAN-HP3型机器人运动学仿真 [J]. J4, 201016, 21(16): 1952-1954,1998.
[15]	苏厚军, 史铁林, 陈非. 高炉煤气透平机状态检修的设计与实施 [J]. J4, 201016, 21(16): 1955-1958.