服役环境下材料蠕变对挤压筒过盈量的影响

摘要/Abstract

摘要： 在传统Lamé公式的基础上引入直接位移求解法（DDM），推导了考虑蠕变效应的挤压筒应力/应变分布解析模型，分析了各层筒应力随时间的变化情况。针对挤压筒用热作模具钢H13进行了高温蠕变试验，获取了500 ℃下热作模具钢H13的蠕变行为和Norton表达式，探讨了材料蠕变对挤压筒各层之间过盈量的影响规律。研究结果表明，交界面处各层筒的蠕变应变有差别，造成径向变形不一，从而使得过盈量减小。

关键词: 挤压筒, 过盈量, 蠕变, H13钢

Abstract: An analytical method, also called direction displacement method (DDM), was proposed based on the Lamé equation to predict the stress/strain evolution in extrusion container. Then, the experiments for evaluating the creep effects of H13 steel at the temperature of 500℃ were conducted, and the creep behavior was modelled by using Norton's law. Finally, a case study was investigated to analyze the relationship between material creep effects and interferences. It is found that the creep strain of each layer in the interface is different, caused the radial deformation is different, thus the interferences are reduced.

Key words: extrusion container, interference, creep effect, H13 steel

中图分类号:

李一红, 罗远新, 马玲, 宋宗焘, 王勇勤. 服役环境下材料蠕变对挤压筒过盈量的影响[J]. 中国机械工程.

Li Yihong, Luo Yuanxin, Ma Ling, Song Zongtao, Wang Yongqin. Creep Effects on Interferences of Extrusion Container with Consideration of Working Conditions[J]. China Mechanical Engineering.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/

http://www.cmemo.org.cn/CN/Y2016/V27/I16/2236

参考文献

[1]王家旺.挤压筒的损坏原因及其补救预防措施[J] .轻合金加工技术，2014，42(3)：41-43.

Wang Jiawang.Causes of Container Failure and Remedy & Prevention Measures [J] .Light Alloy Fabrication Technology，2014，42(3)：41-43.

[2]Sommitsch C，Sievert R，Wlanis T，et al. Modelling of Creep-fatigue in Containers during Aluminium and Copper Extrusion[J].Computational Materials Science，2007，39(1)：55-64.

[3]Sommitsch C，Sievert R，Wlanis T，et al. Lifetime Evaluation of Two Different Hot Work Tool Steels in Aluminium Extrusion[J].Computational Materials Science，2008，43(1)：82-91.

[4]Krumphals F，Wlanis T，Sievert R， et al. Damage Analysis of Extrusion Tools Made from the Austenitic Hot Work Tool Steel Bohler W750 [J].Computational Materials Science，2011，50 (4)：1250-1255.

[5]Krumphals F，Reggiani B，Donati L，et al. Deformation Behaviour of a Ferritic Hot-work Tool Steel with Respect to the Microstructure[J].Computational Materials Science，2012，52(1)：40-45.

[6]Laue K, Stenger H. Extrusion: Processes, Machinery, Tooling[M]. Ohio： American Society for Metals， 1981.

[7]敖文刚，王歆.运用统一强度理论分析预应力组合圆筒分层半径和过盈量[J] .重庆工商大学学报（自然科学版），2011，28(3)：284-288.

Ao Wengang，Wang Xin. Application of Unified Strength Theory to Analysis of Separate Radius and Shrinkrange of Prestressed Combination Tubes[J]. Journal of Chongqing Technology and Business University(Natural Science Edition)，2011，28(3)：284-288.

[8]赵云路，刘静安，陈卫民.圆挤压筒改装成扁挤压筒的试验研究——80 MN挤压机670 mm×270 mm×1600 mm扁挤压筒的设计与制造[J].轻合金加工技术，2001，29(6) ：29-35.

Zhao Yunlu，Liu Jing'an，Zhao Weimin.Trail Study on Refitting Round Container into Flat One in Extrusion Press—Design and Manufacture of 670mm×270mm×1600mm Flat Container in 80MN Press[J].Light Alloy Fabrication Technology，2001，29(6) ：29-35.

[9]谢水生，贺金宇，徐盈辉，等.扁挤压筒结构参数优化及分析研究[J].塑性工程学报，2001，8(4)：26-29.

Xie Shuisheng，He Jinyu，Xu Yinghui，et al. Analyze the Influence of Structure Parameter of Multi-layer Flat Container by FEM[J].Journal of Plasticity Engineering，2001，8(4)：26-29.

[10]李燕，刘全坤，王匀，等.三层预紧扁挤压筒变形及应力分布的数值模拟[J].中国机械工程，2003，14(12)：1074-1076.

Li Yan，Liu Quankun，Wang Yun，et al. Numerical Simulation on Deformation and Stress Distribution of Flat Extruded Container[J].China Mechanical Engineering，2003，14(12)：1074-1076.

[11]刘全坤，王匀.基于Lagrange插值的变过盈量对扁挤压筒变形和强度分析[J].中国机械工程，2004，15(2)：168-170.

Liu Quankun，Wang Jun. Analysis on Deformation and Strength of Flat Container under Changeable Shrink- fitting Range Based on Polynomial Interpolating[J].China Mechanical Engineering，2004，15(2)：168-170.

[12]冯秋红，刘全坤，胡龙飞.基于多目标优化的扁挤压筒结构设计[J].中国机械工程，2006，17(17)：1850-1853.

Feng Qiuhong，Liu Quankun，Hu Longfei. Structural Design of Flat Extrusion Container Based on Multi - objective Optimization[J].China Mechanical Engineering，2006，17(17)：1850-1853.

[13]Luo Yuanxin，Xiong Yikun，Wang Yongqing ，et al.A New Model for Predicting of Stresses on the Compound Extrusion Container[J].WSEAS Transactions on Applied and Theoretical Mechanics，2014，9：229-237.

[14]王玲玲.铝挤压机挤压筒的失效分析[J].锻压技术，2013，38(1)：56-60.

Wang Lingling.Failure Analysis of Extrusion Cylinder for Alumium Extrusion Press[J]. Forging & Stamping Technology，2013，38(1)：56-60.

[15]曹起骧，肖颖，叶绍英.用光电扫描云纹法研究挤压筒壁上的接触应力分布[J].模具技术，1986（2）：1-9.

Cao Qixiang，Xiao Ying，Ye Shaoying. Study on the Cntact Stress Distribution on the Wall of the Extrusion Cylinder by the Photoelectric Scanning Moire Method[J].Die and Mould Technology，1986(2)：1-9.