慢刀伺服车削刀具半径定向补偿的分段逼近求解

doi:10.3969/j.issn.1004-132X.2020.17.001

摘要/Abstract

摘要： 复杂曲面的慢刀伺服车削加工过程中，采用刀具法向补偿算法会在各个直线轴产生补偿量，加工法向矢量突变的曲面时，这种算法并非最优，将补偿量只应用于负载较低的直线轴却是更优的选择。提出一种基于线段逼近的刀具半径定向补偿数值求解算法来求解定向刀位点，通过半径细分的策略使法向误差收敛。算法实例验证及与相关算法的对比结果显示，该算法适用于点云构成的曲面或分段曲面的刀具半径补偿。

关键词: 慢刀伺服, 半径补偿, 复杂曲面, 细分策略

Abstract: In STS turning of complex surfaces, compensated values of all linear servo axes were created by normal cutter compensation algorithm. This algorithm was not optimal when surfaces had sudden changing normal vector，while applying compensated value in linear servo axis with less load was optimal choice. A directional cutter compensation numerical algorithm was introduced based on segment approximation, which might solve the directional compensated value，and the normal error was convergence by further optimization of radius subdivision strategy. Verification of algorithm examples and comparison with related algorithm show that the proposed algorithm may be applied in cutter radius compensation of point cloud surfaces or piecewise surfaces.

Key words: slow tool servo (STS), cutter compensation, complex surface, subdivision strategy

中图分类号:

TH16

李佳伟;杜文浩;韩长庆. 慢刀伺服车削刀具半径定向补偿的分段逼近求解[J]. 中国机械工程, DOI: 10.3969/j.issn.1004-132X.2020.17.001.

LI Jiawei;DU Wenhao;HAN Changqing. Directional Tool Radius Compensation Solution of STS Turning Based on Segment Approximation[J]. China Mechanical Engineering, DOI: 10.3969/j.issn.1004-132X.2020.17.001.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2020.17.001

http://www.cmemo.org.cn/CN/Y2020/V31/I17/2017

参考文献

[1]李荣彬, 张志辉, 杜雪,等. 自由曲面光学元件的设计、加工及面形测量的集成制造技术[J]. 机械工程学报, 2010, 46(11):137-148.
LI Rongbin, ZHANG Zhihui, DU Xue, et al. Integrated Manufacturing Technology for Design, Machining and Measurement of Freeform Optics[J]. Journal of Mechanical Engineering, 2010, 46(11): 137-148.
[2]FANG Fengzhou, ZHANG Xiaodong, WECKENMANN A, et al. Manufacturing and Measurement of Freeform Optics[J]. Manufacturing Technology, 2013, 62(2): 823-846.
[3]WANG Guilin, DAI Yifan, ZHENG Ziwen, et al. Machining Characteristics of Complex Surfaces Using Fast Tool[J]. Machining Science and Technology, 2011, 15(3): 324-337.
[4]王兴盛, 康敏. 基于Hermite插值的复杂光学曲面车削加工路径规划[J]. 机械工程学报, 2012, 48(11):191-198
WANG Xingsheng, KANG Min. Cutting Path Planning for Complex Optical Surface Using Hermite Interpolation[J]. Journal of Mechanical Engineering, 2012, 48(11):191-198.
[5]JI Shijun, YU Huijuan, ZHAO Ji. Two Tool Path Generation Methods for Ultra-precision Machining of Off-axis Convex Ellipsoidal Surface[J]. Journal of Nanoengineering and Nanosystems, 2015, 229(4) :147-153.
[6]石广丰, 史国权, 徐军龙, 等. 慢刀伺服车削渐进多焦点透镜的刀具路径生成与实验[J]. 制造业自动化, 2017, 39(7): 46-53.
SHI Guangfeng, SHI Guoquan, XU Junlong. Tool Path Generation and Experiment of Progressive Addition Lens Based on Slow Tool Servo Turning[J]. Manufacturing Automation, 2017, 39(7): 46-53.
[7]张效栋, 房丰洲, 程颖. 自由曲面超精密车削加工路径优化设计[J]. 天津大学学报, 2009, 42(3): 278-282.
ZHANG Xiaodong, FANG Fengzhou, CHENG Ying. Optimized Design of Cutting Path for Freeform Surface in Ultra-precision Turning[J]. Journal of Tianjin University, 2009, 42(3): 278-282.
[8]关朝亮, 铁贵鹏, 尹自强. 光学阵列器件的慢刀伺服车削加工技术[J]. 国防科技大学学报, 2009, 31(4): 32-35.
GUAN Chaoliang, TIE Guipeng, YIN Ziqiang. Fabrication of Array Lens Optical Component by Using of Slow Tool Servo Diamond Turning[J]. Journal of National University of Defense Technology, 2009, 31(4): 32-35.
[9]郑志浩, 汪国昭. 用三次PH曲线构造平面Bezier曲线的等距偏置算法[J]. 计算机辅助设计与图形学学报, 2004, 16(3): 324-330.
ZHENG Zhihao, WANG Guozhao. Constructing Offset to Planar Bézier Curve by Cubic PH Curve[J]. Journal of Computer Aided Design & Computer Graphics, 2004, 16(3): 324-330.
[10]寿华好, 江瑜, 缪永伟. 基于三次 PH 曲线误差可控代数曲线等距线逼近算法[J]. 图学学报, 2012, 33(4): 30-33.
SHOU Huahao, JIANG Yu, MIAO Yongwei. Error Controllable Algebraic Curve Offset Approximation Based on Cubic PH Curve[J]. Journal of Graphics, 2012, 33(4): 30-33.
[11]YU De Ping, WEI Gan Sze, WONG Yoke San, et al. Optimized Tool Path Generation for Fast Tool Servo Diamond Turning of Micro-structured Surfaces[J]. The International Journal of Advanced Manufacturing Technology, 2012, 63:1137-1152.
[12]周京博. 非回转对称微结构表面超精密车削轨迹及形状误差评价[D]. 哈尔滨：哈尔滨工业大学, 2013.
ZHOU Jingbo. Tool Path Generation and Form Error Evaluation for Ultra-precision Turning of Non-rotational Symmetric Microstructured Surfaces[D]. Harbin: Harbin Institute of Technology, 2013.

[1]	葛科迪, 赵欢, 陈鹏飞, 丁汉. 面向复杂曲面加工的虚拟夹具辅助机器人示教编程研究[J]. 中国机械工程, 2021, 32(14): 1716-1725.
[2]	牛恒泰1;康敏1,2;王兴盛1;杨军1. 渐进多焦点镜片的设计与慢刀伺服车削[J]. 中国机械工程, 2019, 30(06): 722-727.
[3]	赵俊花1;李丽1;李玲玲1;李聪波2. 面向高效节能的复杂曲面分区数控铣削加工优化方法[J]. 中国机械工程, 2019, 30(01): 64-71.
[4]	洪玫;姚立纲. 基于离散模型的内超环面齿轮干涉检验方法[J]. 中国机械工程, 2017, 28(15): 1784-1789.
[5]	孟书云, 赵东标, 陆永华. 复杂曲面自动铺丝轨迹规划算法设计[J]. 中国机械工程, 2016, 27(05): 669-673,679.
[6]	王金涛1;徐金亭2. 复杂曲面上机器人自动喷涂路径规划方法[J]. 中国机械工程, 2015, 26(14): 1916-1919.
[7]	王国勋, 舒启林, 王军, 王宛山 . 复杂曲面五轴加工干涉检查的研究[J]. 中国机械工程, 2014, 25(3): 299-303.
[8]	王峰1, 2, 林浒2, 刘峰1, 2, 郑飂默2, 郑一麟1, 2. 平底刀五轴端铣3D刀补中运动突变的检测算法[J]. 中国机械工程, 2013, 24(15): 1989-1995.
[9]	王兴盛, 康敏. 环曲面眼镜片的慢刀伺服加工技术[J]. 中国机械工程, 2012, 23(18): 2169-2173.
[10]	刘林枝1, 2. 小口径非球面斜轴磨削的砂轮磨损及补偿研究[J]. 中国机械工程, 2012, 23(15): 1789-1792.
[11]	王立成, 黄信达, 丁汉. 原位检测系统中触发式测头的误差分析与补偿[J]. 中国机械工程, 2012, 23(15): 1774-1778.
[12]	李炳林, 王学林, 胡于进, 李成刚. 基于区域划分的刀具方向控制方法 [J]. 中国机械工程, 2010, 21(04): 452-457.
[13]	廖平. 基于粒子群算法和分割逼近法的复杂曲面轮廓度误差计算 [J]. 中国机械工程, 2010, 21(02): 201-205.
[14]	洪海涛;;于东;;张立先;;韩丽;;. 五轴端铣加工中3D刀具半径补偿研究[J]. J4, 2009, 20(15): 0-1889.
[15]	刘健;;计时鸣;. 面向精密抛光的复杂模具曲面三维重构方法[J]. J4, 2009, 20(10): 0-1154.