基于蒙特卡罗仿真的自动仓储系统FEM标准适用性研究

doi:10.3969/j.issn.1004-132X.2020.18.002

摘要/Abstract

摘要：

FEM9.851标准是在自动仓储系统（AS/RS）规划时用于计算出入库效率的一种方法。该标准是针对I/O口在AS/RS不同位置时的适用标准，涵盖2种固定的I/O口位置和4种变化的I/O口位置场景。建立了参数化的AS/RS离散事件仿真模型，对6种I/O口位置进行蒙特卡罗仿真实验，分析FEM9.851标准的适用性。实验结果表明：I/O口位于左下侧、分别位于左右下侧以及I/O口位置相同且在水平方向或垂直方向上变化时，采用FEM9.851标准计算结果与仿真结果吻合，然而，当I/O进出口位置不同，其中一个位置固定在左下侧，另一个位置在垂直方向上变化时，FEM9.851标准出现少量不适用情形。

关键词: 自动仓储系统, FEM9.851标准, 参数化仿真模型, 蒙特卡罗仿真

Abstract:

FEM9.851 standard was a method for calculating warehouse productivity when planning an AS/RS. It was applicable to the input/output(I/O) points in different positions of the AS/RS, covering two fixed I/O point positions and four varying I/O point positions. A parametric AS/RS discrete event simulation model was established. Monte-Carlo simulation experiments were performed on the six I/O point positions in FEM9.851 standard to analyze the applicability. The experimental

results show that FEM9.851 standard calculation results are in good agreement with the simulation results when the I/O points are located on the lower left side , one on the left and another on right lower sides, and the I/O points are in the same position and change in the horizontal or vertical directions. However, when the inbound and outbound positions are different, one of which is fixed on the lower left side and another is changed in the vertical direction, FEM9.851 standard shows a small amount of inapplicability.

Key words: automated storage and retrieval system（AS/RS）, FEM9.851 standard, parametric simulation model, Monte-Carlo simulation

中图分类号:

TP273

赵宁1；罗鑫珍1；李文英1；袁召云2. 基于蒙特卡罗仿真的自动仓储系统FEM标准适用性研究[J]. 中国机械工程, DOI: 10.3969/j.issn.1004-132X.2020.18.002.

ZHAO Ning1；LUO Xinzhen1；LI Wenying1；YUAN Zhaoyun2. Suitability about FEM Standard on AS/RS with Monte-Carlo Simulation[J]. China Mechanical Engineering, DOI: 10.3969/j.issn.1004-132X.2020.18.002.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2020.18.002

http://www.cmemo.org.cn/CN/Y2020/V31/I18/2153

参考文献

[1]ROODBERGEN K J, VIS I F A. A Survey of Literature on Automated Storage and Retrieval Systems[J]. European Journal of Operational Research, 2009, 194(2):343-362.
[2]ROUWENHORSTA B, REUTERB B, STOCKRAHMB V, et al. Warehouse Design and Control:Framework and Literature Review[J]. European Journal of Operational Research, 2000, 122(3):515-533.
[3]SARKER B R, BABU P S. Travel Time Models in Automated Storage/Retrieval Systems:a Critical Review[J]. International Journal of Production Economics, 1995, 40(2/3):173-184.
[4]GAGLIARDI J P, RENAUD J, RUIZ A. Models for Automated Storage and Retrieval Systems:a Literature Review[J]. International Journal of Production Research, 2012, 50(24):7110-7125.
[5]LERHER T, SRAML M, KRAMBERGER J,et al. Analytical Travel Time Models for Multi Aisle Automated Storage and Retrieval Systems[J]. The International Journal of Advanced Manufacturing Technology, 2006, 30(3/4):340-356.
[6]GU J X, GOETSCHALCKX M, MCGINNIS L F. Resarch on Warehouse Design and Performance Evaluation:a Comprehensive Review[J]. European Journal of Operational Research, 2010, 203(3):539-549.
[7]秦叙斌.有轨巷道堆垛起重机入出库能力的计算[J]. 起重运输机械, 2001(11):9-11.
QIN Xubin. Calculation of Productivity of Automated Storage/Retrieval Machine[J]. Hoisting and Conveying Machinery, 2001(11):9-11.
[8]LERHER T, SRAML M, POTRC I. Simulation Analysis of Mini-load Multi-shuttle Automated Storage and Retrieval Systems[J]. The International Journal of Advanced Manufacturing Technology, 2011, 54(1):337-348.
[9]AZZI A, BATTINI D, FACCIO M, et al. Innovative Travel Time Model for Dual-shuttle Automated Storage/Retrieval Systems[J]. Computers & Industrial Engineering, 2011, 61(3):600-607.
[10]MELLER R D, MUNGWATTANA A. Multi-shuttle Automated Storage/Retrieval Systems[J]. IIE Transactions,1997,29(10):925-938.
[11]MELLER R.D MUNGWATTANA A. AS/RS Dwell-point Strategy Selection at High System Utilization:a Simulation Study to Investigate the Magnitude of the Benefit[J]. International Journal of Production Research, 2005, 43(24):5217-5227.
[12]宋宇博, 蒋兆远, 孙秉珍. 多端口出入式自动化存取系统作业集成优化[J]. 中南大学学报(自然科学版), 2016, 51(6):1930-1939.
SONG Yubo, JIANG Zhaoyuan, SUN Bingzhen. Integrated Optimization of Operations in Multiple-I/O Points Automated Storage and Retrieval System[J]. Journal of Central South University(Science and Technology), 2016, 51(6):1930-1939.
[13]RAMTIN F, PAZOUR J A. Analytical Models for an Automated Storage and Retrieval System with Multiple In-the-aisle Pick Positions[J]. IIE Transactions, 2014, 46(9):968-986.
[14]ROSENBLATT M J, ROLL Y, ZYSER V. A Combined Optimization and Simulation Approach for Designing Automated Storage/Retrieval Systems[J]. IIE Transactions, 1993, 25(1):40-50.
[15]赵宁，董绍华，王国华.基于三阶段仿真法的AS/RS物流系统规划[J].北京科技大学学报, 2007， 29(10):1054-1059.
ZHAO Ning, DONG Shaohua, WANG Guohua. AS/RS Planning Based on Three-phase Simulation[J]. Journal of University of Science and Technology Beijing, 2007, 29(10):1054-1059.
[16]HAN M H , MCGINNIS L F , SHIEH J S , et al. On Sequencing Retrievals in an Automated Storage/Retrieval System[J]. IIE Transactions, 1987, 19(1):56-66.
[17]PETERS B A. Analysis of Dual-shuttle Automated Storage/Retrieval Systems[J]. Journal of Manufacturing Systems, 1994, 13(6):424-434.
[18]GUO J, ZHAO N, SUN L, et al. Modular Based Flexible Digital Twin for Factory Design[J]. Journal of Ambient Intelligence and Humanized Computing, 2019, 10(3):1189-1200.
[19]ZHAO N, LUO L, LODEWIJKS G. Scheduling Two Lifts on a Common Rail Considering Acceleration and Deceleration in a Shuttle Based Storage and Retrieval System[J]. Computers & Industrial Engineering, 2018, 124:48-57.
[20]ZHAO Ning, LUO Lei, ZHANG Saipeng, et al. An Efficient Simulation Model for Rack Design in Multi-elevator Shuttle-based Storage and Retrieval System[J]. Simulation Modelling Practice and Theory, 2016, 67:100-116.
[21]赵虎,赵宁,张赛朋.结合价值流程图与数字孪生技术的工厂设计[J]. 计算机集成制造系统, 2019,25(6):1481-1490.
ZHAO Hu, ZHAO Ning, ZHANG Saipeng. Factory Design Approach Based on Value Stream Mapping and Digital Twin[J]. Computer Integrated Manufacturing Systems, 2019, 25(6):1481-1490.
[22]赵宁,穆云,徐传标,等. 基于RESTART方法的同轨多天车仿真调度[J].系统工程理论与实践, 2016,36(7):1826-1836.
ZHAO Ning, MU Yun, XU Chuanbiao,et al. Multi-crane Scheduling Based on Repetitive Simulation Trials after Reaching Thresholds[J]. Systems Engineering-Theory & Practice, 2016, 36(7):1826-1836.