[成形过程仿真优化与集成计算材料工程]注射成形熔体喷射的三维模拟及消除对策研究

doi:10.3969/j.issn.1004-132X.2020.22.008

摘要/Abstract

摘要： 为了探寻塑料注射成形过程中熔体喷射的消除对策，采用高精度离散格式追踪熔体流动前沿，基于有限体积法离散控制方程，发展了三维数值算法。与实验结果对比发现：所发展算法能有效模拟壁厚为4 mm的长方体型腔内的两种喷射演化模式以及厚壁型腔内的熔体喷射及其演化过程；小壁厚型腔内熔体的屈曲呈二维折叠演化，厚壁型腔内熔体的屈曲呈三维缠绕演化；重力对厚壁型腔内的喷射演化产生影响。通过增大剪切速率即改变熔体流动速度大小或者流动方向能有效消除或抑制喷射现象，并且用两个数值算例论证了该观点。

关键词: 消除对策, 剪切速率, 数值模拟, 喷射, 注射成形

Abstract: To explore the elimination countermeasures of melt jetting phenomenon in plastic injection molding, a high resolution discrete scheme was used to track the melt front. The governing equations were discretized by finite volume method and a three dimensional algorithm was developed. Comparing to experimental results, the two modes of molding filling under jetting conditions in the cuboid cavity with 4 mm thickness and the evolution of jetting in thick cavity were successfully simulated numerically. It is found that the jet buckling presents two-dimensional folding in the cuboid cavity with small thickness and three-dimensional roiling in thick cavity. Gravity has an impact on the evolution of jetting in thick cavity. Jetting might be effectively eliminated or depressed via enlarging shear rate with changing the magnitude or the direction of velocity. Two numerical cases were performed to verify the views.

Key words: elimination countermeasure, shear rate, numerical simulation, jetting, injection molding

中图分类号:

TQ320.66

花少震, 孟凡净, 刘华博, 丁海. [成形过程仿真优化与集成计算材料工程]注射成形熔体喷射的三维模拟及消除对策研究[J]. 中国机械工程, DOI: 10.3969/j.issn.1004-132X.2020.22.008.

HUA Shaozhen, MENG Fanjing, LIU Huabo, DING Hai. Study on Three Dimensional Simulation and Elimination Countermeasures of Melt Jetting Phenomenon in Injection Molding[J]. China Mechanical Engineering, DOI: 10.3969/j.issn.1004-132X.2020.22.008.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2020.22.008

http://www.cmemo.org.cn/CN/Y2020/V31/I22/2715

参考文献

［1］严志云, 谢鹏程, 丁玉梅, 等. 基于可视化技术对注射成形喷射现象的研究［J］. 塑料, 2010， 39(3):103-106.
YAN Zhiyun, XIE Pengcheng, DING Yumei, et al. The Jetting Phenomenon of Injection Molding Based on Visualization Technology［J］. Plastics, 2010， 39(3):103-106.
［2］杨卫民, 丁玉梅, 谢鹏程, 等.注射成型新技术［M］.北京:化学工业出版社, 2008：378.
YANG Weimin, DING Yumei, XIE Pengcheng,et al. New Technology of Injection Molding［M］. Beijing：Chemical Industry Press,2008：378.
［3］ODA K, WHITE J L, CLARK E S. Jetting Phenomena in Injection Mold Filling Mold Filling［J］. Polymer Engineering & Science, 1976, 16(8):585-592.
［4］OZDEMIR A, ULUER O, GULDA??塁 A. Flow Front Advancement of Molten Thermoplastic Materials during Filling Stage of A Mold Cavity ［J］. Poly-mer Testing, 2004, 23(8):957-966.
［5］孙翔,杨卫民,丁玉梅,等.基于可视化的注射成形制品缺陷及其产生机理的研究［J］.中国塑料,2005,13(12):64-68.
SUN Xiang, YANG Weimin, DING Yumei, et al. Studyon Defects of Injection Molded Parts and Their Generation Mechanism Based on Visualization［J］. China Plastics, 2005,13(12):64-68.
［6］张世勋,曹伟,叶曙兵, 等. 高速微注射成形中熔体充填模式及裹气机理研究［J］.中国塑料,2012,26(1):65-70.
ZHANG Shixun, CAO Wei, YE Shubing, et al. Studyon Melt Filling Mode and Trapping Air Mechanism in High Speed Micro-injection Molding［J］. China Plastics, 2012, 26(1):65-70.
［7］花少震,曹伟,张世勋, 等. 注塑成型喷射现象数值模拟及机理分析［J］.应用力学学报,2016,33(4):707-713.
HUA Shaozhen, CAO Wei, ZHANG Shixun, et al. Numerical Simulation and Mechanism Analysis for Jetting Phenomenon during Injection Molding［J］, Chinese Journal of Applied Mechanics, 2016,33(4):707-713.
［8］杜彬, 安瑛, 严志云, 等. 矩形型腔熔体充填规律的可视化实验［J］. 塑料, 2010, 39(6):1-4.
DU Bin, AN Ying, YAN Zhiyun , et al. Visualization Experiment of the Melt Filling Behavior in Rectangle Cavity［J］. Plastics, 2010, 39(6):1-4.
［9］欧相麟,王大中,周起雄，等.注塑件喷射纹的形成机理及其解决措施［J］.塑料工业,2012,40(5):44-48.
OU Xianglin, WANG Dazhong, ZHOU Qixiong, et al. Formation Mechanism of Jetting in Injection Parts and Solving Measures［J］. China Plastics Industry, 2012,40(5):44-48.
［10］KRAMSCHUSTER A, PILLA S, GONG S, et al. Injection Molded Solid and Microcellular Polylactide Compounded with Recycled Paper Shopping Bag Fibers［J］. International Polymer Processing,2007,22(5):436-445.
［11］GOODSHIP V. Troubleshooting Injection Moulding［R］∥Rapra Review Reports. Goodrich：iSmithers Rapra Publishing, 2004，15（4）：1-135.
［12］CHAU S W, LIN Y W. Three-dimensional Simulation of Melt Filling and Gas Penetration in Gas-assisted Injection Molding Process Using a Finite Volume Formulation［J］. Journal of Polymer Engineering, 2006, 26(5):431-450.
［13］MICHAELI W, HOFFMANN S, KRATZ M, et al. Simulation Opportunities by a Three-dimensional Calculation of Injection Moulding Based on the Finite Element Method［J］. International Polymer Processing , 2001, 16(4):398-403.
［14］ZHANG Shixun, HUA Shaozhen, CAO Wei, et al. 3D Viscoelastic Simulation of Jetting in Injection Molding ［J］. Polymer Engineering & Science, 2019, 59(S2):397-405.
［15］UBBINK O, ISSA R I. A Method for Capturing Sharp Fluid Interfaces on Arbitrary Meshes［J］. Journal of Computational Physics, 1999, 153(1):26-50.
［16］TADMOR Z, GOGOS C G. Principles of Polymer Processing［M］. Hoboken ：John Wiley & Sons, 2013：766-766.
［17］花少震,孟凡净.注塑成型喷射现象的实验及数值研究［J］.西安交通大学学报,2019,53(9):88-95.
HUA Shaozhen,MENG Fanjing.Experimental and Numerical Research on Jetting Phenomenon during Injection Molding［J］.Journal of Xian Jiaotong University, 2019,53(9):88-95.
［18］KAMAL M R, KENIG S. The Injection Molding of Thermoplastics Part I:Theoretical Model ［J］. Polymer Engineering & Science, 2010, 12(4):294-301.
［19］CROWSON R, FOLKES M. Rheology of Short Glass Fiber-reinforced Thermoplastics and Its Application to Injection Molding. Ⅱ. The Effect of Material Parameters［J］. Polymer Engineering & Science, 1980, 20(14):934-940.

[1]	李燕乐, 潘忠涛, 戚小霞, 崔维强, 陈健, 李方义. 热处理工艺对激光熔覆316L温度场与应力场的影响规律[J]. 中国机械工程, 2024, 35(04): 666-677.
[2]	彭文飞, 张成, 林龙飞, 黄明辉, 余丰. 基于连续损伤力学的楔横轧芯部损伤建模及预测[J]. 中国机械工程, 2024, 35(04): 711-720,751.
[3]	李坤航, 张思琦, 吴玮, 胡明卓, 孙娅铃, 熊鑫, 黄宏. 三层异种不等厚钢电阻点焊多场耦合模拟与分析[J]. 中国机械工程, 2023, 34(24): 2996-3003.
[4]	高昆, 任延岫, 朱悦, 齐乐华, 罗俊. 飞机钛合金蒙皮战伤便携气动铣切试验研究[J]. 中国机械工程, 2023, 34(19): 2320-2326.
[5]	骆文泽, 成慧梅, 刘红艳, 王义峰, 叶延洪, 邓德安. 高强钢Q960E对接接头残余应力与焊接变形的数值模拟[J]. 中国机械工程, 2023, 34(17): 2095-2105,2141.
[6]	刘莹, 陈越, 赵雪利, 于同敏, 祝铁丽, . 超声辅助注射成形碳纤维增强聚丙烯制件性能研究[J]. 中国机械工程, 2023, 34(16): 1975-1981.
[7]	朱玉龙, 赵迎松, 方阳, 陈洪恩, 陈振茂, . 孔边裂纹的旋转涡流检测[J]. 中国机械工程, 2023, 34(08): 883-891.
[8]	秦登, 戴志远, 周宁, 李田. 受电弓下沉对其气动和声学行为的影响[J]. 中国机械工程, 2022, 33(20): 2509-2519.
[9]	李伟, 郑颢, 刘彦梅, 范松. 汽车副车架安装螺栓碰撞断裂的数值模拟研究[J]. 中国机械工程, 2022, 33(19): 2388-2393.
[10]	胡福泰, . 薄壁扇形筋板挤压成形开裂抑制及翻转展宽策略[J]. 中国机械工程, 2022, 33(14): 1734-1740.
[11]	马艺, 陈宇涛, 孟祥铠, 赵文静, 彭旭东, . 牙轮钻头用单金属密封瞬态启动动力学模型与密封性能[J]. 中国机械工程, 2022, 33(07): 777-785.
[12]	许明三, 周春辉, 张正, 曾寿金, . 激光熔覆过程中的粉、气、光耦合温度场[J]. 中国机械工程, 2022, 33(01): 70-77.
[13]	潘承怡, 童圆栖, 曹冠群, 赵彦玲. 微结构表面展开轮摩擦磨损特性与仿真研究[J]. 中国机械工程, 2021, 32(22): 2689-2696.
[14]	朱谦, 游东东, 朱权利, . 基于摩擦模型的挤压铸造机压射机构动态配合[J]. 中国机械工程, 2021, 32(12): 1405-1413.
[15]	尹洪超, 刘宵, 翟镇德, 穆林. 多角度弯曲管磨粒流加工数值模拟研究[J]. 中国机械工程, 2021, 32(11): 1299-1306.