液压四足机器人足端的力预测控制与运动平稳性

doi:10.3969/j.issn.1004-132X.2021.05.003

摘要/Abstract

摘要： 针对液压四足机器人在坚硬路面行走时，足端位置易受刚性冲击，导致运动姿态平稳性差的问题，提出一种液压四足机器人足端力预测控制方法。在分析液压四足机器人结构的基础上，根据运动学与力学模型构建了液压伺服系统的力控制模型；采用改进自适应布谷鸟优化BP神经网络算法建立足端力预测控制模型，通过仿真对比分析验证了该算法的可行性。最后通过液压四足机器人KL样机进行足端力及刚性地面行走测试，结果表明该方法能有效增强液压四足机器人腿部的力柔顺性，提高运动姿态平稳性。

关键词: 液压四足机器人, 预测控制, 布谷鸟算法, BP神经网络

Abstract: Aiming at the problem that plantar position of hydraulic quadruped robot is susceptible to rigid impacts when walking on hard roads, which is resulted in poor motion posture stability, a method for predicting plantar force of the hydraulic quadruped robot was proposed. On the basis of analyzing structure of the hydraulic quadruped robot, a force control model of hydraulic servo system according to kinematics and mechanics model was constructed. Then, an improved adaptive cuckoo optimized BP neural network algorithm was used to establish plantar force predictive control model, feasibility of the algorithm was verified with simulation and comparative analysis. Finally, a KL prototype of the hydraulic quadruped robot was used to test for the plantar force of rigid ground walking. The results show that the method may effectively enhance leg flexibility of the hydraulic quadruped robot and improve stability of motion posture.

Key words: hydraulic quadruped robot, predictive control, cuckoo algorithm, BP neural network

中图分类号:

TP242.6

李冰1;张永德1;袁立鹏2;朱光强3;代雪松1;苏文海3. 液压四足机器人足端的力预测控制与运动平稳性[J]. 中国机械工程, DOI: 10.3969/j.issn.1004-132X.2021.05.003.

LI Bing1;ZHANG Yongde1;YUAN Lipeng2;ZHU Guangqiang3;DAI Xuesong1;SU Wenhai3. Predictive Control of Plantar Force and Motion Stability of Hydraulic Quadruped Robot[J]. China Mechanical Engineering, DOI: 10.3969/j.issn.1004-132X.2021.05.003.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2021.05.003

http://www.cmemo.org.cn/CN/Y2021/V32/I05/523

参考文献

［1］余联庆,王玉金,王立平,等. 基于机体翻转的四足机器人翻越台阶过程的运动学分析［J］. 中国机械工程，2012，23(5)：518-524.
YU Lianqing, WANG Yujin, WANG Liping, et al. Kinematics Analysis of Quadruped Robot Climbing Step Based on Body Flipping［J］. China Mechanical Engineering, 2012, 23(5):518-524.
［2］汪红波,余联庆,王玉金,等. 具有翻滚模式的可变形四足机器人结构设计与分析［J］. 中国机械工程，2012，23(22)：2743-2747.
WANG Hongbo, YU Lianqing, WANG Yujin, et al. Design and Analysis of a Transformable Quadruped with Rolling Mode［J］. China Mechanical Engineering, 2012, 23(22):2743-2747.
［3］雷静桃,俞煌颖,王峰.四足机器人对角小跑步态动态稳定步行足端非连续约束及动力学建模［J］. 中国机械工程，2015，26(5)：592-597.
LEI Jingtao, YU Huangying, WANG Feng.Analysis on Non-continuous Constraints and Dynamics Modeling of Quadruped Robot Dynamically Stable Walking with Trot Gait［J］. China Mechanical Engineering, 2015, 26(5):592-597.
［4］VIDONI R，GASPARETTO A. Efficient Force Distribution and Led Posture for a Bio-inspired Spider Robot［J］. Robotics and Autonomous Systems, 2011, 59(2):142-150.
［5］李鑫. 基于虚拟模型和阻抗控制的四足液压驱动机器人行走研究［D］. 哈尔滨：哈尔滨工业大学，2018.
LI Xin. Research on Walking of Hydraulically Driven Quadruped Robot Based on Virtual Model and Impedance Control［D］. Harbin:Harbin Institute of Technology, 2018.
［6］张国腾. 四足机器人主动柔顺及对角小跑步态运动控制研究［D］. 济南：山东大学，2016.
ZHANG Guoteng. Research on Active Compliance and Trotting Gait Control of a Quadruped Robot［D］. Jinan:Shandong University, 2016.
［7］丁庆鹏. 基于阻抗控制的四足仿生机器人稳定步态理论及实验研究［D］. 哈尔滨：哈尔滨工业大学，2016.
DING Qingpeng. Theory and Experimental Research on Stable Gait of Quadruped Robot Based on Impedance Control［D］. Harbin:Harbin Institute of Technology, 2016.
［8］苏文海,李冰,闫聪杰,等. 基于复合粒子群自适应液压伺服系统力跟踪控制与试验［J］. 东北农业大学学报，2018，49(1)：85-96.
SU Wenhai, LI Bing, YAN Congjie, et al. Force Tracking Control and Test of Adaptive Hydraulic Servo System Based on Composite Particle Swarm Optimization［J］. Journal of Northeast Agricultural University, 2018, 49(1):85-96.
［9］俞滨,巴凯先,王佩,等. 四足机器人液压驱动单元变刚度和变阻尼负载特性的模拟方法［J］. 中国机械工程，2016，27(18)：2458-2466.
YU Bin, BA Kaixian, WANG Pei, et al.Simulation Method of Variable Stiffness and Damping Load Characteristics on Hydraulic Drive Unit of a Quadruped Robot［J］. China Mechanical Engineering, 2016, 27(18):2458-2466.
［10］柯贤锋,王军政,何玉东,等. 基于力反馈的液压足式机器人主/被动柔顺性控制［J］. 机械工程学报，2017，53(1)：13-20.
KE Xianfeng, WANG Junzheng, HE Yudong, et al.Active/Passive Compliance Control for a Hydraulic Quadruped Robot Based on Force Feedback［J］. Journal of Mechanical Engineering, 2017, 53(1):13-20.
［11］邵璇,张永德,孙桂涛,等. 液压四足机器人内力抑制及实验研究［J］. 仪器仪表学报，2018，39(9)：73-81.
SHAO Xuan, ZHANG Yongde, SUN Guitao, et al. Inner Force Inhibit and Experiment Research of Hydraulic Quadruped Robot［J］. Chinese Journal of Scientific Instrument, 2018, 39(9); 73-81.
［12］柴汇. 液压驱动四足机器人柔顺及力控制方法的研究与实现［D］. 济南：山东大学，2016.
CHAI Hui. Research and Implementation on Compliance and Force Control of Hydraulically Actuated Quadruped Robot［D］. Jinan:Shandong University, 2016.
［13］邵璇. 液压四足机器人力平衡控制研究［D］. 哈尔滨:哈尔滨理工大学，2018.
SHAO Xuan. Research on Force Balance Control of Hydraulic Quadruped Robot［D］. Harbin:Harbin University of Science and Technology, 2018.
［14］ZHANG Xiuli, ZHENG Haojun, XU Guan, et al. A Biological Inspired Quadruped Robot:Structure and Control［C］∥IEEE International Conference on Robotics and Biomimetics. Hong Kong, 2005:387-392.
［15］MEEK S, KIM J, ANDERSON M. Stability of a Trotting Quadruped Robot with Passive, Underactuated Legs［C］∥IEEE International Conference on Robotics and Automation. Pasadena, 2008:347-351.
［16］李满天,蒋振宇,郭伟,等. 四足仿生机器人单腿系统［J］.机器人，2014，36(1)：21-28.
LI Mantian, JIANG Zhenyu, GUO Wei, et al. Leg Prototype of a Bio-inspired Quadruped Robot［J］.2014, 36(1):21-28.
［17］常青,韩宝玲,罗庆生. 四足机器人改进型对角小跑步态研究［J］. 中国机械工程，2015，26(18)：2426-2431.
CHANG Qing, HAN Baoling, LUO Qingsheng. Study on an Improved Trot Gait for Quadruped Robot［J］. China Mechanical Engineering, 2015, 26(18):2424-2431.
［18］苏文海,李冰,袁立鹏,等.立体坡面农业四足移动平台姿态控制策略与试验［J］. 农业工程学报，2018，34(4)：80-91.
SU Wenhai, LI Bing, YUAN Lipeng, et al. Strategy and Experiment of Attitude Control for Quadruped Mobile Platform Walking on Three-dimensional Slope Used for Agriculture［J］. Transactions of the Chinese Society of Agricultural Engineering, 2018, 34(4):80-91.
［19］谢惠祥,尚建忠,罗自荣,等. 四足机器人对角小跑中\\机体翻转分析与姿态控制［J］. 机器人 2014，36(6)：676-682.
XIE Huixiang, SHANG Jianzhong, LUO Zirong, et al. Body Rolling Analysis and Attitude Control of a Quadruped Robot during Trotting［J］. Robot, 2014, 36(6):676-682.
［20］纪华伟,刘毛娜,胡小平. 基于混合遗传算法的磁控形状记忆合金驱动器磁滞模型优化［J］. 中国机械工程，2015，26(4)：508-512.
JI Weihua, LIU Maona, HU Xiaoping. Optimization of MSMA Actuator Hysteresis Model Based on Hybrid GA［J］.China Mechanical Engineering, 2015. 26(4):508-512.
［21］陈永亮,彭涛,刘德帅,等. 面向现场加工的全液压驱动主轴水下钻孔特性建模与优化方法［J］. 中国机械工程，2018，29(4)：471-476.
CHEN Yongliang, PENG Tao, LIU Deshuai, et al. Characteristic Modeling and Optimization Method of Underwater Hydraulic Spindle Drilling Processes for In-situ Machining Systems［J］. China Mechanical Engineering, 2018, 29(4):471-476.
［22］刘大玲,黄小钢.高速铁路无砟轨道系统状态监测及预防性维修［J］. 中国机械工程，2019，30(3)：349-353.
LIU Daling, HUANG Xiaogang. Condition Monitoring and Preventive Maintenance of Ballastless Track Systems for High-speed Railways［J］.China Mechanical Engineering, 2019, 30(3):349-353.
［23］NAWI N M, KHAN A, REHMAN M Z. A New Back-Propagation Neural Network Optimized with Cuckoo Search Algorithm［C］∥Proceedings of the 13th International Conference on Computational Science and Its Applications. Ho Chi Minh City, 2013:413-426.
［24］CHEN J F, DO Q H. Forecasting Daily Electricity Load by Wavelet Neural Networks Optimized by Cuckoo Search Algorithm［J］. Neurocomputing, 2017, 182:18-132.
［25］MANICKAVASAGAM R, SELVAN S. Automatic Detectionand Classification of Lung Nodules in CT Image Using Optimized Neuro Fuzzy Classifier with Cuckoo Search Algorithm［J］. Journal of Medical Systems, 2019, 43(3):77-86.
［26］李扬,吴敏渊,邹炼.基于布谷鸟算法的BP神经网络图像复原［J］. 计算机应用，2017，37(增刊1)：173-175.
LI Yang, WU Minyuan, ZOU Lian.BP Neural Network for Image Restoration Based on Cuckoo Algorithm［J］. Journal of Computer Applications, 2017, 37(S1):173-175.
［27］叶文,李翔晟,单外平. 基于改进布谷鸟搜索优化神经网络的AMT换挡电机控制［J］. 计算机应用，2018，38(增刊2)：67-71.
YE Wen, LI Xiangsheng, SHAN Waiping. Control of AMT Shift Motor Based on Improved CS Algorithm to Optimize Neaural Network［J］.Journal of Computer Applications, 2018, 38(S2):67-71.
［28］周瑞红. 基于群智能优化理论的聚类改进方法及应用研究［D］. 长春：吉林大学，2017.
ZHOU Ruihong. Improved Clustering Methods Based on Swarm Intelligence Theories and Their Applications［D］. Changchun:Jilin University, 2017.
［29］WANG Jiesheng, HAN Shuang, SHEN Nana, et al. Features Extraction of Flotation Froth Images and BP Neural Network Soft-sensor Model of Concentrate Grade Optimized by Shuffled Cuckoo Searching Algorithm［J］. The Scientific World Journal, 2014, 2014:208094.
［30］贾涵,连晓峰.发现概率参数自适应调节的布谷鸟改进算法［J］. 计算机工程与应用，2018，54(22)：16-22.
JIA Han, LIAN Xiaofeng. Improved Cuckoo Algorithm for Adaptive Adjustment of Discovery Probability Parameter［J］. Computer Engineering and Applications, 2018, 54(22):16-22.

[1]	刘俊玲, 冯港辉, 张俊江, 杨凯. 无人驾驶混合动力汽车轨迹跟踪节能控制融合研究[J]. 中国机械工程, 2024, 35(04): 678-690.
[2]	徐美姣, 薛善良, 张惠, 周国庆, 卢红根. 基于BP-AdaBoost算法的复杂产品装配制造成熟度等级评估方法[J]. 中国机械工程, 2023, 34(20): 2513-2519.
[3]	雷勇, 赵威, 何宁, 李亮. TC17钛合金低温铣削表面粗糙度预测[J]. 中国机械工程, 2022, 33(05): 583-588.
[4]	雷超凡, 初秀民, 柳晨光, 吴文祥, 李松龙, . 船闸水域船舶列队协同停船预测控制器[J]. 中国机械工程, 2022, 33(04): 421-431.
[5]	张峰峰, 张欣, 陈龙, 孙立宁, 詹蔚. 采用改进遗传算法优化神经网络的双目相机标定[J]. 中国机械工程, 2021, 32(12): 1423-1431.
[6]	夏光, 李嘉诚, 唐希雯, 张洋, 陈无畏. 平衡重式叉车防侧翻模型预测控制研究[J]. 中国机械工程, 2021, 32(08): 987-996.
[7]	韩玲, 刘鸿祥, 曹越, 任磊磊. 基于模型预测控制的无级变速起步优化控制策略[J]. 中国机械工程, 2020, 31(15): 1765-1771.
[8]	白国星1;孟宇1,2;刘立1;顾青1;罗维东1;甘鑫1. 基于可变预测时域及速度的车辆路径跟踪控制[J]. 中国机械工程, 2020, 31(11): 1277-1284.
[9]	肖帆;李光;游雨龙. 空间3R机械手逆向运动学的多模块神经网络求解[J]. 中国机械工程, 2019, 30(10): 1233-1238.
[10]	刘大玲, 黄小钢. [制造与维修工艺]高速铁路无砟轨道系统状态监测及预防性维修[J]. 中国机械工程, 2019, 30(03): 349-353.
[11]	钟祾充, 钱斌, 胡蓉, 王凌. [车间调度]混合布谷鸟算法求解绿色流水车间调度问题[J]. 中国机械工程, 2018, 29(22): 2674-2681.
[12]	钱立军1;荆红娟1;邱利宏1，2. 基于随机模型预测控制的四驱混合动力汽车能量管理[J]. 中国机械工程, 2018, 29(11): 1342-1348.
[13]	权凌霄1, 2;郭海鑫1,3;盛世伟3;李雷1. 采用“GA+LM”优化BP神经网络的电液伺服阀故障诊断[J]. 中国机械工程, 2018, 29(05): 505-510.
[14]	陈永亮1;彭涛1;刘德帅1;王志江2. 面向现场加工的全液压驱动主轴水下钻孔特性建模与优化方法[J]. 中国机械工程, 2018, 29(04): 471-476.
[15]	邱利宏, 钱立军, 杜志远, 王金波. 车联网环境下车辆最优车速闭环快速模型预测控制[J]. 中国机械工程, 2017, 28(10): 1245-1252.