剪滞效应对复合材料固化变形影响的数值分析

doi:10.3969/j.issn.1004-132X.2021.05.014

摘要/Abstract

摘要： 通过分析固化过程中热、化学收缩及材料性能之间的多场耦合，建立了复合材料固化变形的三维数值仿真模型。预测结果与试验结果的对比，证明了所建模型具有较高的计算精度。基于所建模型，研究了剪滞效应的机理及影响，结果表明：剪滞效应随着构件厚度的增大而增强，但构件转角半径对剪滞效应的影响很小；剪滞效应是影响构件固化变形的一个重要因素，构件固化变形随着剪滞效应的增强而减小。

关键词: 复合材料, 固化变形, 剪滞效应, 数值模拟

Abstract: By analyzing the multi-field coupling of thermal, chemical shrinkage and material properties during curing, a three-dimensional numerical simulation model for curing deformation of composites was established. By comparing the predicted results with the experimental ones, it is proved that the simulation model has high computational accuracy. Based on the established simulation model, the physical mechanism and influences of the shear-lag effect were analyzed. Results show that the shear-lag effect increases with the increase of the part thickness, while the influences of the part corner radius on the shear-lag effect are insignificant. The shear-lag effect is an important factor affecting the curing deformation of parts, and the curing deformation decreases with the enhancement of shear-lag effect.

Key words: composite, curing deformation, shear-lag effect, numerical simulation

中图分类号:

TB332

乔巍1;姚卫星1,2. 剪滞效应对复合材料固化变形影响的数值分析[J]. 中国机械工程, DOI: 10.3969/j.issn.1004-132X.2021.05.014.

QIAO Wei1;YAO Weixing1,2. Numerical Analysis of Shear-lag Effect on Curing Deformation of Composites[J]. China Mechanical Engineering, DOI: 10.3969/j.issn.1004-132X.2021.05.014.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2021.05.014

http://www.cmemo.org.cn/CN/Y2021/V32/I05/611

参考文献

［1］崔海坡，温卫东. 复合材料层合板冲击损伤影响因素分析［J］. 中国机械工程, 2008, 19(5):613-617.
CUI Haipo，WEN Weidong. Influence Factor Analysis for Impact Damage of Composite Laminate［J］.China Mechanical Engineering, 2008, 19(5):613-617.
［2］干年妃，王多华，冯亚楠，等. 聚氨酯泡沫填充的碳纤维增强复合材料锥管吸能性能数值模拟及试验验证［J］. 中国机械工程, 2018, 29(5):609-615.
GAN Nianfei, WANG Duohua, FENG Yanan, et al. Numerical Simulation and Experimental Verification of Energy Absorption Performance of PU Foam Filled CFRP Cone Tubes［J］. China Mechanical Engineering, 2018, 29(5):609-615.
［3］BOGETTI T A, GILLESPIE J W. Process-induced Stress and Deformation in Thick-section Thermoset Composite Laminates［J］. Journal of Composite Materials, 1992, 26(5):626-660.
［4］郭章新，韩小平，李金强，等. 纤维缠绕复合材料固化过程残余应力/应变的三维数值模拟［J］. 复合材料学报, 2014, 31(4):1006-1012.
GUO Zhangxin, HAN Xiaoping, LI Jinqiang, et al. Three-dimensional Numerical Simulation of Residual Stress/Strain for Filament-wound Composites during Curing Process［J］. Acta Materiae Compositae Sinica, 2014, 31(4):1006-1012.
［5］马云荣，贺继林，李栋，等. 树脂基复合材料曲面结构件固化变形数值模拟［J］. 复合材料学报, 2015, 32(3):874-880.
MA Yunrong, HE Jilin, LI Dong, et al. Numerical Simulation of Curing Deformation of Resin Matrix Composite Curved Structure［J］. Acta Materiae Compositae Sinica, 2015, 32(3):874-880.
［6］WHITE S, KIM Y. Process-induced Residual Stress Analysis of AS4/3501-6 Composite Material［J］. Mechanics of Composite Materials & Structures, 1998, 5(2):153-186.
［7］ZOCHER M A, GROVES S E, ALLEN D H. A Three-dimensional Finite Element Formulation for Thermoviscoelastic Orthotropic Media［J］. International Journal for Numerical Methods in Engineering, 1997, 40(12):2267-2288.
［8］闵荣，元振毅，王永军，等. 基于黏弹性本构模型的热固性树脂基复合材料固化变形数值仿真模型［J］. 复合材料学报, 2017, 34(10):2254-2262.
MIN Rong, YUAN Zhenyi, WANG Yongjun，et al. Numerical Simulation for Curing Deformation of Resin Matrix Thermosetting Composite Using Viscoelastic Constitutive Model［J］. Acta Materiae Compositae Sinica, 2017, 34(10):2254-2262.
［9］张江涛，尚云东，张梅，等. 复合材料固化相关黏弹性性能演化及残余应力分析［J］. 复合材料学报, 2017, 34(5):978-986.
ZHANG Jiangtao, SHANG Yundong, ZHANG Mei，et al. Analysis on the Process Dependent Viscoelastic Properties and Residual Stresses of Composites during Cure［J］. Acta Materiae Compositae Sinica, 2017, 34(5):978-986.
［10］SVANBERG J M, HOLMBERG J A. Prediction of Shape Distortions PartⅠ. FE-implementation of a Path Dependent Constitutive Model［J］. Composites Part A:Applied Science & Manufacturing, 2004, 35(6):711-721.
［11］SVANBERG J M, HOLMBERG J A. Prediction of Shape Distortions. PartⅡ. Experimental Validation and Analysis of Boundary Conditions［J］. Composites Part A:Applied Science & Manufacturing, 2004, 35(6):723-734.
［12］乔巍，姚卫星，马铭泽. 复合材料残余应力和固化变形数值模拟及本构模型评价［J］. 材料导报, 2019, 33(24):4193-4198.
QIAO Wei, YAO Weixing, MA Mingze. Numerical Simulation and Constitutive Models Evaluation of Residual Stresses and Process-induced Deformations of Composite Structures［J］. Materials Reports, 2019, 33(24):4193-4198.
［13］WISNOM M R, POTTER K D, ERSOY N. Shear-lag Analysis of the Effect of Thickness on Spring-in of Curved Composites［J］. Journal of Composite Materials, 2007, 41(11):1311-1324.
［14］王乾，关志东，王仁宇，等. 结构参数对复合材料V型构件固化变形影响试验及解析分析［J］. 复合材料学报, 2017, 34(12):2722-2733.
WANG Qian, GUAN Zhidong, WANG Renyu, et al. Experimental and Analytic Analysis of the Structure Parameters on Process-induced Distortions of V-shaped Composite Part［J］. Acta Materiae Compositae Sinica, 2017, 34(12):2722-2733.
［15］DING A, LI S, WANG J, et al. Prediction of Process-induced Distortions in L-shaped Composite Profiles Using Path-dependent Constitutive Law［J］. Applied Composite Materials, 2016, 23(5):1-19.
［16］KIM Y K, WHITE S R. Stress Relaxation Behavior of 3501-6 Epoxy Resin during Cure［J］. Polymer Engineering & Science, 1996, 36(23):2852-2862.
［17］GARSTKA T, ERSOY N, POTTER K D, et al. In Situ Measurements of Through-the-thickness Strains during Processing of AS4/8552 Composite［J］. Composites Part A:Applied Science & Manufacturing, 2007, 38(12):2517-2526.
［18］LI C, POTTER K, WISNOM M R, et al. In-Situ Measurement of Chemical Shrinkage of MY750 Epoxy Resin by a Novel Gravimetric Method［J］. Composites Science & Technology, 2004, 64(1):55-64.
［19］BRAUNER C, BAUER S, HERRMANN A S. Analysing Process-induced Deformation and Stresses Using a Simulated Manufacturing Process for Composite Multispar Flaps［J］. Journal of Composite Materials, 2015, 49(4):387-402.
［20］BAPANAPALLI S K, SMITH L V. A Linear Finite Element Model to Predict Processing-induced Distortion in FRP Laminates［J］. Composites Part A:Applied Science & Manufacturing. 2005, 36(12):1666-1674.

[1]	李燕乐, 潘忠涛, 戚小霞, 崔维强, 陈健, 李方义. 热处理工艺对激光熔覆316L温度场与应力场的影响规律[J]. 中国机械工程, 2024, 35(04): 666-677.
[2]	彭文飞, 张成, 林龙飞, 黄明辉, 余丰. 基于连续损伤力学的楔横轧芯部损伤建模及预测[J]. 中国机械工程, 2024, 35(04): 711-720,751.
[3]	康仁科, 陆冰伟, 陈凯良, 李晟超, 戴晶滨, 董志刚鲍, 岩. 超声振动辅助磨削CFRP复合材料薄管撕裂损伤研究[J]. 中国机械工程, 2024, 35(03): 524-533，540.
[4]	张立峰, 王梓旭, 张旺通, 邓云飞, 隋翯, 郭志永. 单向陶瓷基复合材料C/SiC变角度顺逆磨的对比试验[J]. 中国机械工程, 2024, 35(02): 235-243.
[5]	李坤航, 张思琦, 吴玮, 胡明卓, 孙娅铃, 熊鑫, 黄宏. 三层异种不等厚钢电阻点焊多场耦合模拟与分析[J]. 中国机械工程, 2023, 34(24): 2996-3003.
[6]	朱福先, 仇刚, 朱兴民, 徐先宜, 周金宇. 碳玻混杂复合材料单钉单剪螺栓连接结构失效模式及渐进损伤分析[J]. 中国机械工程, 2023, 34(23): 2781-2793.
[7]	张立峰, 张晓光. 微量润滑变角度高速铣削碳纤维增强复合材料的加工性能与材料去除机理[J]. 中国机械工程, 2023, 34(21): 2622-2628.
[8]	杨亮, 蔡桂喜, 刘芳, 李建奎. 碳纤维复合材料制孔结构超声无损检测及评价[J]. 中国机械工程, 2023, 34(19): 2327-2332.
[9]	闫东东, 胡宇博, 郎利辉, 秦成伟, 张三敏, 李勇. 大跨距复合材料结构弯曲载荷监测及定位方法[J]. 中国机械工程, 2023, 34(18): 2257-2267.
[10]	骆文泽, 成慧梅, 刘红艳, 王义峰, 叶延洪, 邓德安. 高强钢Q960E对接接头残余应力与焊接变形的数值模拟[J]. 中国机械工程, 2023, 34(17): 2095-2105,2141.
[11]	王飞, 凤仪, 李新朝, 刘铸汉. Cu-Diamond复合材料的多次电弧烧蚀性能研究[J]. 中国机械工程, 2023, 34(13): 1599-1604.
[12]	彭翔, 江浩浩, 郭玉良, 李吉泉, 易兵, 姜少飞, . 机翼蒙皮铺层顺序和材料布局协同优化[J]. 中国机械工程, 2023, 34(12): 1415-1424,1435.
[13]	朱玉龙, 赵迎松, 方阳, 陈洪恩, 陈振茂, . 孔边裂纹的旋转涡流检测[J]. 中国机械工程, 2023, 34(08): 883-891.
[14]	刘小峰, 张天瑀, 张春兵, 柏林. 基于交叉递归率的复材板损伤定位成像方法[J]. 中国机械工程, 2023, 34(08): 940-947.
[15]	王轩, 马瑞云, 周春苹. 挖补修理平纹编织面板蜂窝夹芯结构侧向压缩渐进失效机理[J]. 中国机械工程, 2023, 34(06): 727-738.