基于三组测量绳结构的软体机械臂运动检测

doi:10.3969/j.issn.1004-132X.2021.06.012

摘要/Abstract

摘要： 针对气动软体机械臂运动形状检测问题，设计了一种基于拉线编码器的三组测量绳结构的运动学参数检测装置。依据分段常曲率法，构建了气动模块化软体机械臂的运动检测模型，基于机械臂柔性材料的特点，在建模过程中引入刚度法，使检测模型能准确反映从机械臂驱动气压到形状变化以及运动学参数的映射关系。提出了一种可模块化组装的气动软体机械臂，用于验证检测装置与模型的精度，所提出的机械臂在构型上由硅胶基体、运动气囊和连接板组成，能实现机械臂的模块化组装。通过对所构建的运动检测模型进行推导与仿真，得到了模型的相对误差。最后，通过试验验证了运动检测建模的精度和机械臂驱动、构型以及运动的特征。研究结果表明：相比于传统的视觉追踪方法，所设计的基于三组测量绳结构的检测装置能实现对软体机械臂运动形状的高精度检测。

关键词: 软体机械臂, 模块化设计, 分段常曲率法, 运动检测

Abstract: For detecting the movement shape of pneumatic soft manipulators, a kinematic parameter detection device was designed with a measure structure of three wires based on wire-drawing encoders. According to piece-wise constant curvature method, the motion detection model was established for soft manipulator with pneumatic modularization. Based on flexible material characteristics of manipulators, the stiffness method was introduced to derive the map from actuation pressure to configuration shape and kinematic parameters precisely. A novel soft manipulator with pneumatic modularization was presented to verify the accuracy of modelling and the device. The presented manipulator was consisted of silicon backbone, motion chambers and connecting plates for modularizing assembly. The relative errors of motion detection model were obtained via derivation and simulation. Finally, the accuracy of modelling and the features of manipulator in actuation, configuration and movement were verified by tests. The results showed that compared with traditional visual tracking method, the designed device achieved the highly precise detection for movement shapes of soft manipulators.

Key words: soft manipulator, modular design, piece-wise constant curvature method, motion detection

中图分类号:

TP242

李敬仪, 姚立纲, 东辉. 基于三组测量绳结构的软体机械臂运动检测[J]. 中国机械工程, 2021, 32(06): 721-728.

LI Jingyi, YAO Ligang, DONG Hui. Motion Detection for Soft Manipulators Based on Three-wire Structures[J]. China Mechanical Engineering, 2021, 32(06): 721-728.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2021.06.012

http://www.cmemo.org.cn/CN/Y2021/V32/I06/721

参考文献

［1］韩奉林, 李鹏, 李明辉,等. 颗粒流驱动变刚度弯曲软体驱动器的设计及运动仿真［J］. 中国机械工程, 2020, 31(8):890-897.

HAN Fenglin, LI Peng, LI Minghui, et al. Design and Motion Simulation of Variable Stiffness Bending Soft Actuators Driven by Granular Flow［J］. China Mechanical Engineering, 2020, 31(8):890-897.

［2］姚立纲, 李敬仪, 东辉. 气动软体机械臂模块变刚度性能分析［J］. 机械工程学报, 2020, 56(9):50-58.

YAO Ligang，LI Jingyi，DONG Hui. Variable Stiffness Analysis on a Pneumatic Soft Manipulator［J］. Journal of Mechanical Engineering, 2020, 56(9):50-58.

［3］姚建涛，陈新博，陈俊涛，等. 软体机械手遥操作系统的设计与分析［J］. 中国机械工程，2020，31(16): 1968-1977.

YAO Jiantao, CHEN Xinbo, CHEN Juntao, et al. Design and Analysis of Soft Manipulator Teleoperation Systems［J］. China Mechanical Engineering, 2020, 31(16)：1968-1977.

［4］FALCO I D, CIANCHETTI M, MENCIASSI A. A Soft Multi-module Manipulator with Variable Stiffness for Minimally Invasive Surgery［J］. Bioinspiration & Biomimetics, 2017, 7: 1-16.

［5］RENDA F, CACUCCIOLO V, DIAS J, et al. Discrete Cosserat Approach for Soft Robot Dynamics: a New Piece-wise Constant Strain Model with Torsion and Shears［C］//IEEE/RSJ International Conference on Intelligent Robots and Systems(IROS). Daejeon, 2016: 5495-5502.

［6］王超. 基于光纤光栅传感器的软体机械臂三维形状检测方法［J］. 化工自动化及仪表，2015，42(10): 1130-1133.

WANG Chao. 3D Shapes Detecting Method of Soft Manipulator Based on Fiber Bragg Grating Sensor［J］. Control and Instruments in Chemical Industry, 2015，42(10): 1130-1133.

［7］田加文，王田苗，史震云，等. 仿象鼻机械臂的运动学分析及实验［J］. 机器人, 2017, 39(5): 585-594.

TIAN Jiawen, WANG Tianmiao, SHI Zhenyun, et al. Kinematic Analysis and Experiment of an Elephant-trunk-like Robot Arm［J］. Robot, 2017, 39(5): 585-594.

［8］闫继宏，石培沛，张新彬，等. 软体机械臂仿生机理、驱动及建模控制研究发展综述［J］. 机械工程学报, 2018, 54(15): 1-14.

YAN Jihong, SHI Peipei, ZHANG Xinbin, et al. Review of Biomimetic Mechanism, Actuation, Modeling and Control in Soft Manipulators［J］. Journal of Mechanical Engineering, 2018, 54(15): 1-14.

［9］范需, 戴宁, 王宏涛, 等. 气动网格软体驱动器弯曲变形预测方法［J］. 中国机械工程，2020, 31(9):1108-1114.

FAN Xu， DAI Ning， WANG Hongtao，et al. Bending Deformation Prediction Method of Soft Actuators with Pneumatic Networks［J］. China Mechanical Engineering, 2020, 31(9):1108-1114.

［10］MAHL T, HILDERRANDT A, SAWODNY O. A Variable Curvature Continuum Kinematics for Kinematic Control of the Bionic Handling Assistant［J］. IEEE Transactions on Robotics, 2014, 30(4): 935-949.

［11］YAO L, LI J, LIU X, et al. The Multi-section Design of a Novel Soft Pneumatic Robot Arm with Variable Stiffness［C］//International Conference on Intelligent Robotics and Applications(ICIRA). Shenyang, 2019: 596-607.

［12］GONG Z, XIE Z, YANG X, et al. Design Fabrication and Kinematic Modeling of 3D-motion Soft Robotic Arm［C］//IEEE International Conference in Robotics and Biomimetics. Qingdao, 2016:509-514.

［13］WEBSTER R J, JONES B A. Design and Kinematic Modeling of Constant Curvature Continuum Robots: a Review［J］. International Journal of Robotics Research, 2010, 11: 1-56.

［14］WALKER I D. Continuous Backbone “Continuum” Robot Manipulators［J］. ISRN Robotics, 2013, 7:1-19.

［15］PAYREBRUNE K M D, OLIVER O M. On the Development of Rod-based Models for Pneumatically Actuated Soft Robot Arms:a Five-parameter Constitutive Relation［J］. International Journal of Solids and Structures, 2017, 120:226-235.

［16］SADATI S M H, NAGHIBI S E, WALKER I D, et al. Control Space Reduction and Real-time Accurate Modeling of Continuum Manipulators Using Ritz and Ritz-Galerkin Methods［J］. IEEE Robotics and Automation Letters, 2018, 3(1):328-335.

［17］WANG H, WANG C, CHEN W, et al. Three Dimensional Dynamics for Cable-driven Soft Manipulator［J］. IEEE/ASME Transactions on Mechatronics, 2017, 22(1):18-28.

［18］CHEN Y, LIANG J, HUNTER I W. Modular Continuum Robotic Endoscope Design and Path Planning［C］//IEEE International Conference on Robotics & Automation(ICRA). Hong Kong, 2014:5393-5400.

［19］ABAYAZID M, KEMP M, MISRA S. 3D Flexible Needle Steering in Soft-tissue Phantoms Using Fiber Bragg Grating Sensors［C］//IEEE International Conference on Robotics & Automation(ICRA). Karlsruhe, 2013:5843-5849.

［20］WANG X, GENG T, ELSAYED Y, et al. A New Coefficient-adaptive Orthonormal Basis Function Model Structure for Identifying a Class of Pneumatic Soft Actuators［C］// IEEE/RSJ International Conference on Intelligent Robots & Systems. Chicago, 2014:530-535.

［21］YANG W, DONG W, DU Z. Kinematics Modeling for a Kinematic Mechanics Coupling Continuum Manipulator［C］// International Conference on Manipulation, Manufacturing and Measurement on the Nanoscale(3M-NANO). Taipei, 2014:95-99.

［22］NIKU S B. Introduction to Robotics—Analysis, Control, Applications［M］. 2nd ed. New Jersey:Wiley, 2010.

[1]	王封旭, 邢志广, 杨朋朋, 林俊, 赵建文, . 基于低熔点合金相变的变刚度软体机械臂稳态传热研究[J]. 中国机械工程, 2021, 32(07): 793-798.
[2]	程贤福1;周健1;肖人彬2;刘俊杰1;游敏华1. 面向绿色制造的产品模块化设计研究综述[J]. 中国机械工程, 2020, 31(21): 2612-2625.
[3]	李浩, 陶飞, 文笑雨, 王昊琪, 罗国富. [产品服务系统]面向大规模个性化的产品服务系统模块化设计[J]. 中国机械工程, 2018, 29(18): 2204-2214,2249.
[4]	肖超, 周玉林, 盛海泳, 侯雨雷. 工业机器人机械本体模块化设计[J]. 中国机械工程, 2016, 27(08): 1018-1025.
[5]	王科, 黄智, 钟志华. 尾随运动车辆识别与超车检测方法研究[J]. 中国机械工程, 2013, 24(3): 415-421.
[6]	李浩1, 祁国宁2, 纪杨建2, 顾新建2. 面向服务的产品模块化设计方法及其展望[J]. 中国机械工程, 2013, 24(12): 1687-1695.
[7]	毛雨辉. 基于一种改进聚类算法的雷达导引头产品功能模块划分方法研究 [J]. 中国机械工程, 2010, 21(03): 314-319.
[8]	李桂东;周来水;安鲁陵;谭昌柏;. 基于八元集合模板和专用模块的产品快速设计方法研究[J]. J4, 2009, 20(19): 0-2392.
[9]	赵利平;王宗彦;秦慧斌;董良;. 面向大规模定制的堆垛机快速设计系统研究[J]. J4, 2008, 19(18): 0-2161.