低匹配对接接头的抗冲击等承载设计方法

doi:10.3969/j.issn.1004-132X.2021.06.013

中国机械工程 ›› 2021, Vol. 32 ›› Issue (06): 729-733.DOI: 10.3969/j.issn.1004-132X.2021.06.013

低匹配对接接头的抗冲击等承载设计方法

董志波;卢伟泽;相靓宇;方洪渊

哈尔滨工业大学先进焊接与连接国家重点实验室，哈尔滨，150001

出版日期:2021-03-25 发布日期:2021-04-01
作者简介:董志波，男，1975年生，教授。研究方向为复杂结构焊接应力与变形的高效、高精度计算方法，焊缝微观组织、微观应力应变场和微观缺陷的定量研究，焊接接头等承载设计方法与设计准则。E-mail: dongzhb@hit.edu.cn。
基金资助:
国家自然科学基金（51875131）

Design Method of Undermatching Butt Joints for ELC of Impact Resistance

DONG Zhibo;LU Weize;XIANG Jingyu;FANG Hongyuan

State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin, 150001

Online:2021-03-25 Published:2021-04-01

摘要/Abstract

摘要： 针对A921高强钢低匹配焊接接头抗冲击承载能力不足的问题，基于等承载的思想提出了以冲击功为承受冲击载荷能力的参量，并以此建立了等承载关系。通过A921钢试件的夏比冲击试验，发现其材料冲击韧度与抗弯能力之间具有线性关系，并获得了冲击韧度与构件几何尺寸之间的定量关系。通过Q345钢试件的冲击试验验证了上述关系依然成立，表明该线性关系具备一定的可推广性。如果两材料均满足该关系，则可以借助该关系对比材料的冲击韧性，并预测不同尺寸试件受冲击的力学响应。为此，提出了材料的抗冲击等承载设计方案：通过计算使母材与焊接接头断裂消耗冲击功相等的最佳接头厚度，将其作为冲击载荷下等承载接头的设计条件，并结合接头几何参数优化方法，实现材料的抗冲击等承载设计。

关键词: 冲击载荷, 冲击功, 等承载, 设计方法

Abstract: In order to solve the problems of insufficient impact load-carrying capacity of undermatching butt joints of A921 high-strength steel，based on the idea of ELC, the impact energy was taken as the parameter of the load-carrying capacity of impact load, and the relationship of ELC was established. Through Charpy impact tests of A921 steel specimen, it is found that there is a linear relationship between impact toughness and bending resistance, and the quantitative relationship between the impact toughness and component geometry size is obtained. The impact test results of Q345 steel specimen show that the relationship is still valid, which indicates that the relationship may be generalized to a certain extent. The impact toughness of two materials may be compared and the mechanics response of specimens with different sizes may be predicted by this relationship. Finally, the design scheme of ELC impact resistance was proposed: the optimal joint thickness was calculated to make the base metal and the welded joint fracture consume the same impact energy, then making the thickness as the design conditions of ELC joints under the impact loads, thus the design was carried out in combination with the geometric parameter optimization method of ELC joints.

Key words: undermatching joint, impact load, impact energy, equal load carrying(ELC), design method

中图分类号:

TG407

董志波, 卢伟泽, 相靓宇, 方洪渊. 低匹配对接接头的抗冲击等承载设计方法[J]. 中国机械工程, 2021, 32(06): 729-733.

DONG Zhibo, LU Weize, XIANG Jingyu, FANG Hongyuan. Design Method of Undermatching Butt Joints for ELC of Impact Resistance[J]. China Mechanical Engineering, 2021, 32(06): 729-733.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2021.06.013

http://www.cmemo.org.cn/CN/Y2021/V32/I06/729

参考文献

［1］TONG L, NIU L, JING S, et al. Low Temperature Impact Toughness of High Strength Structural Steel［J］. Thin-Walled Structures, 2018, 132: 410-420.

［2］SHIOZAKI T, YAMAGUCHI N, TAMAI Y, et al. Effect of Weld Toe Geometry on Fatigue Life of Lap Fillet Welded Ultra-high Strength SteelJoints［J］. International Journal of Fatigue, 2018, 116: 409-420.

［3］张晓波, 曹睿, 冯伟, 等. 980MPa高强钢TIG焊接接头原位拉伸断裂机理［J］. 中国机械工程, 2010, 21(22): 2746-2750.

ZHANG Xiaobo, CAO Rui, FENG Wei, et al. Fracture Mechanism of In-situ Tensile of TIG Welding Joints for 980MPa High Strength Steels［J］. China Mechanical Engineering, 2010, 21(22): 2746-2750.

［4］刘雨桐, 袁朝龙, 吴任东, 等. 基于压缩试验法的P91韧性断裂行为研究［J］. 中国机械工程, 2016, 27(16): 2254-2258.

LIU Yutong, YUAN Chaolong, WU Rendong, et al. Study on P91 Alloy Ductile Fracture Behavior Based on Compressing Experiment［J］. China Mechanical Engineering, 2016, 27(16): 2254-2258.

［5］宋威. 高强钢低匹配十字焊接接头疲劳行为研究［D］. 哈尔滨：哈尔滨工业大学, 2019.

SONG Wei. Research on Fatigue Behavior of High Strength Steel Undermatched Cruciform Welded Joints［D］. Harbin：Harbin Institute of Technology, 2019.

［6］郭军礼, 董志波, 刘雪松, 等. 基于等承载思想的低匹配T型接头设计［J］. 机械工程学报, 2019, 55(6): 1-10.

GUO Junli, DONG Zhibo, LIU Xuesong, et al. Design of Undermatching T Joints Based on the Thought of Equal Load Carrying Capacity［J］. Journal of Mechanical Engineering, 2019, 55(6): 1-10.

［7］方洪渊. 焊接结构的等承载设计［J］. 黑龙江科学, 2018, 9(2): 27-30.

FANG Hongyuan. Welding Structure of Equal Bearing Design［J］. Heilongjiang Science, 2018, 9(2): 27-30.

［8］赵智力, 杨建国, 方洪渊, 等. 基于等承载能力原则的低匹配对接接头设计［J］. 焊接学报, 2008, 29(10): 93-96.

ZHAO Zhili, YANG Jianguo, FANG Hongyuan, et al. Design of Undermatching Butt Joint Based on Equal Load Carrying Capacity Principle［J］. Transactions of the China Welding Institution, 2008, 29(10): 93-96.

［9］赵智力. 基于等承载能力原则的高强钢低匹配焊接接头设计［D］. 哈尔滨：哈尔滨工业大学, 2009.

ZHAO Zhili. Design of Undermatching Welded Joints for High Strength Steels Based on Principle of the Equal Load-carrying Capacity［D］. Harbin：Harbin Institute of Technology, 2009.

［10］赵智力, 方洪渊, 杨建国, 等. 一种针对低匹配焊接接头的“等承载”设计方法［J］. 焊接学报, 2011, 32(4): 87-90.

ZHAO Zhili, FANG Hongyuan, YANG Jianguo, et al. The Invention Relates to a Design Method of Equal-load for Undermatching Welded Joint［J］. Transactions of the China Welding Institution, 2011, 32(4): 87-90.

［11］潘建华. 冲击载荷作用下压力容器用金属材料动态断裂行为的研究［D］. 合肥：中国科学技术大学, 2013.

PAN Jianhua. Dynamic Fracture Behavior of Pressure Vessel Metal Materials under Impact Loads［D］. Hefei：University of Science and Technology of China, 2013.

［12］HAO S, SCJWALBE K H, CORNEC A. The Effect of Yield Strength Mis-match on the Fracture Analysis of Welded Joints: Slip-line Field Solutions for Pure Bending［J］. International Journal of Solids and Structures, 2000, 37(39): 5385-5411.

[1]	欧阳志高, 李坚, 吴立强, 艾兴, 章的. 薄壁机匣结构复杂冲击载荷与等效试验方法研究[J]. 中国机械工程, 2020, 31(14): 1754-1761.
[2]	刘世豪, 林茂. [综述]高速数控转台优化设计方法研究现状与展望[J]. 中国机械工程, 2020, 31(13): 1629-1637.
[3]	钟浩龙;张小龙;刘子建. 薄壁梁结构的电动汽车车身刚度正向设计方法[J]. 中国机械工程, 2020, 31(08): 975-982.
[4]	刘晓昂1,2,3;焦湘和2,3;武一民1,2,3. 汽车独立悬架后桥悬置系统设计方法研究[J]. 中国机械工程, 2020, 31(05): 535-542.
[5]	王连东1;刘超1,2;刘恒1;王晓迪3;王志鹏1. 芯轴外径对大变形推压-拉拔复合缩径的影响[J]. 中国机械工程, 2018, 29(17): 2131-2136.
[6]	康乐, 李建兰, 严野, 刘念. 考虑冲击载荷影响的性能退化型产品可靠性研究[J]. 中国机械工程, 2014, 25(5): 587-591.
[7]	王时龙, 田波, 周杰, 赵昱, 程成. 多股簧冲击载荷特性试验研究[J]. 中国机械工程, 2014, 25(21): 2925-2929.
[8]	张克华, 闵力, 丁金福, 许永超, 程光明 . 磨料流微去除力学分析与可控因素影响[J]. 中国机械工程, 2014, 25(18): 2432-2438.
[9]	刘志峰, 詹一飞, 李新宇, 成焕波. 温度-压强耦合并行激发主动拆卸结构的设计方法研究[J]. 中国机械工程, 2014, 25(18): 2484-2489.
[10]	盖江涛, 黄守道, 周广明, 李慎龙. 双侧电机驱动的功率耦合机构传动方案设计方法[J]. 中国机械工程, 2014, 25(13): 1739-1743.
[11]	景春晖, 赵江洪. 基于进化思想的汽车造型优化设计方法研究[J]. 中国机械工程, 2014, 25(11): 1517-1523.
[12]	崔亚平, 王连东, 杨立云, 杨东峰. 胀-压复合成形汽车桥壳预成形管坯的设计及成形试验[J]. 中国机械工程, 2012, 23(21): 2577-2580.
[13]	王美焰1, 沈连婠1, 邓益民2, 束学道2. 基于E-CBP的机电产品可持续概念设计方法[J]. 中国机械工程, 2012, 23(13): 1603-1607.
[14]	刘志峰, 张敬东, 成焕波. 基于ABAQUS显式动力学的PCB板跌落研究[J]. 中国机械工程, 2012, 23(12): 1456-1461.
[15]	付振明1, 金玉谟1, 孟繁忠2. 一种V型发动机正时链系统的设计方法 [J]. 中国机械工程, 2011, 22(17): 2132-2135.

低匹配对接接头的抗冲击等承载设计方法

Design Method of Undermatching Butt Joints for ELC of Impact Resistance

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics