考虑时变间隙的并联指向机构非线性模态分析

doi:10.3969/j.issn.1004-132X.2021.14.008

中国机械工程 ›› 2021, Vol. 32 ›› Issue (14): 1700-1708,1715.DOI: 10.3969/j.issn.1004-132X.2021.14.008

考虑时变间隙的并联指向机构非线性模态分析

孙静1,2;韩雪艳1,2;魏元浩1,2;陈爽1,2;李仕华1,2

1.燕山大学机械工程学院，秦皇岛，066004
2.燕山大学河北省并联机器人与机电系统实验室，秦皇岛，066004

出版日期:2021-07-25 发布日期:2021-08-04
通讯作者: 李仕华（通信作者），男，1966生，教授、博士研究生导师。研究方向为并联机器人技术及理论、机构动力学。E-mail:shli@ysu.edu.cn。
作者简介:孙静，男，1989年生，博士研究生。研究方向为机构动力学，并联机器人技术及理论。
基金资助:
国家自然科学基金(51775475);
河北省军民融合项目(2020B030)

Nonlinear Modal Analysis of Parallel Pointing Mechanisms Considering Time-varying Clearances

SUN Jing1,2;HAN Xueyan1,2;WEI Yuanhao1,2;CHEN Shuang1,2;LI Shihua1,2

1.School of Mechanical Engineering,Yanshan University,Qinhuangdao,Hebei,066004
2.Parallel Robot and Mechatronic System Laboratory of Hebei Province,Yanshan University,Qinhuangdao,Hebei,066004

Online:2021-07-25 Published:2021-08-04

摘要/Abstract

摘要： 针对复杂空间机构的振动模型难以建立的问题，基于数轴法提出一种简便的并联指向机构振动模型建模方法，利用ANSYS模态分析证明了该方法的可行性。为了研究运动副间隙对机构模态特性的动态影响规律，考虑运动副残余刚度，提出了含间隙运动副的改进非线性等效刚度系数建立方法。将改进的非线性等效刚度系数嵌入机构振动模型，建立了考虑时变运动副间隙的非线性振动模型。利用ADAMS对考虑间隙的机构动力学进行仿真分析，根据仿真得到的间隙数据对受时变间隙影响的机构非线性模态特性进行分析。研究结果可以为并联指向机构的动态性能优化、振动抑制和故障诊断提供理论依据。

关键词: 振动系统建模, 残余刚度, 运动副间隙, 非线性模态

Abstract: Aiming at the problems that it was difficult to establish the vibration model of the complex space mechanisms, a simple modeling method of the vibration model of the parallel pointing mechanisms was proposed based on the number axis method, and the feasibility of the method was proved by the ANSYS modal analysis. In order to study the dynamic influences of the clearances of the kinematic pair on the modal characteristics of the mechanisms, considering the residual stiffness of the kinematic pairs, an improved method for establishing the nonlinear equivalent stiffness coefficient of the kinematic pairs with clearances was proposed. The improved nonlinear equivalent stiffness coefficient was embedded in the mechanism vibration model, and a nonlinear vibration model was established considering the clearances of the time-varying kinematic pairs. The ADAMS was used to simulate the dynamics of the mechanisms considering the clearances. According to the simulation data, the nonlinear modal characteristics of the mechanisms affected by the time-varying clearances were analyzed. The research results may provide a theoretical basis for the dynamic performance optimization, vibration suppression and fault diagnosis of the parallel pointing mechanisms.

Key words: vibration system modeling, residual stiffness, clearance of kinematic pair, nonlinear modal

中图分类号:

TH113.1

孙静, 韩雪艳, 魏元浩, 陈爽, 李仕华, . 考虑时变间隙的并联指向机构非线性模态分析[J]. 中国机械工程, 2021, 32(14): 1700-1708,1715.

SUN Jing, HAN Xueyan, WEI Yuanhao, CHEN Shuang, LI Shihua, . Nonlinear Modal Analysis of Parallel Pointing Mechanisms Considering Time-varying Clearances[J]. China Mechanical Engineering, 2021, 32(14): 1700-1708,1715.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2021.14.008

http://www.cmemo.org.cn/CN/Y2021/V32/I14/1700

参考文献

［1］韩雪艳, 李仕华, 左亚铭, 等. 考虑磨损后含间隙指向机构运动特性［J］. 中国空间科学技术, 2018, 38(4):51-61.
HAN Xueyan, LI Shihua, ZUO Yaming, et al. Kinematics of a Pointing Mechanism with Clearance After Considering Wear［J］. China Space Science and Technology, 2018， 38(4):51-61.
［2］李艳清, 江俊. 含间隙弹簧振动系统的非线性模态特性［J］. 动力学与控制学报, 2015, 13(1):28-36.
LI Yanqing, JIANG Jun. Nonlinear Modal Characteristics of a Spring Vibration System with Clearance［J］. Journal of Dynamics and Control, 2015, 13(1):28-36.
［3］张艳龙, 唐斌斌, 王丽, 等. 动摩擦作用下含间隙碰撞振动系统的动力学分析［J］. 振动与冲击, 2017, 36(24):63-68.
ZHANG Yanlong, TANG Binbin, WANG Li, et al. Dynamic Analysis of Impact Vibration System with Gap under Dynamic Friction［J］. Journal of Vibration and Shock, 2017, 36(24):63-68.
［4］李新泉, 刘池, 李海泉, 等. 一类两自由度含间隙碰撞振动系统的动力学特性［J］. 甘肃科技纵横, 2018, 47(3):17-19.
LI Xinquan, LIU Chi, LI Haiquan, et al. Dynamic Characteristics of a Two-degree-of-freedom Impact Vibration System with Clearance［J］. Gansu Science and Technology, 2018, 47(3):17-19.
［5］唐俊杰, 晏紫琦, 蔡敢为, 等. 含间隙可控式码垛机器人强度与模态分析［J］. 机械设计与研究, 2019, 35(4):11-14.
TANG Junjie, YAN Ziqi, CAI Ganwei, et al. Strength and Modal Analysis of a Controllable Palletizing Robot with Clearance［J］. Machine Design and Research, 2019, 35(4):11-14.
［6］尹凤伟, 罗冠炜, 同长虹. 含间隙-弹性约束振动系统周期冲击振动多样性及规律特征［J］. 振动与冲击, 2020, 39(24):1-10.
YIN Fengwei, LUO Guanwei, TONG Changhong. Periodic Shock Vibration Diversity and Regular Characteristics of a Vibration System with Gaps and Elastic Constraints［J］. Journal of Vibration and Shock, 2020, 39(24):1-10.
［7］ZHAO Nanyang , MAO Zhiwei, WEI Donghai, et al. Fault Diagnosis of Diesel Engine Valve Clearance Based on Variational Mode Decomposition and Random Forest［J］. Applied Sciences, 2020, 10(3)：1124.
［8］王强, 马志赛, 张欣, 等. 基于模态综合法的含间隙折叠舵面动态特性分析［J］. 航空学报, 2020, 41(5):202-210.
WANG Qiang, MA Zhisai, ZHANG Xin, et al. Dynamic Characteristics Analysis of Folding Rudder Surface with Clearance Based on Modal Synthesis Method［J］. Acta Aeronautica Sinica, 2020, 41(5):202-210.
［9］SUN Jing, SHAO Lei, FU Lifei,et al. Kinematic Analysis and Optimal Design of a Novel Parallel Pointing Mechanism［J］. Aerospace Science and Technology, 2020, 104：105931.
［10］白艳艳, 张晓俊. 建立弹簧-质量-阻尼系统数学模型的数轴法［J］. 噪声与振动控制, 2012, 32(3):59-62.
BAI Yanyan, ZHANG Xiaojun. Numerical Axis Method for Establishing Mathematical Model of Spring-mass-damping System［J］. Noise and Vibration Control, 2012, 32(3):59-62.
［11］陈旭，李建中. 结构动力分析中Rayleigh阻尼合理取值研究［J］. 结构工程师, 2013, 29(5):28-33.
CHEN Xu, LI Jianzhong. Research on Reasonable Value of Rayleigh Damping in Structural Dynamic Analysis ［J］. Structural Engineer, 2013, 29 (5):28-33.
［12］刘福才, 兰会, 刘林, 等. 不同重力环境下含间隙旋转铰位置特性仿真研究［J］. 振动与冲击, 2018, 37(21):240-246.
LIU Fucai, LAN Hui, LIU Lin, et al. Simulation Study on the Position Characteristics of the Rotating Hinge with Clearance under Different Gravity Environments［J］. Vibration and Shock, 2018, 37(21):240-246.
［13］王旭鹏, 刘更, 马尚君, 等. 间隙铰链对平面机构碰撞动力学特性影响分析［J］. 振动与冲击, 2017， 36(17)：74-78.
WANG Xupeng, LIU Geng, MA Shangjun, et al. Analysis of the Influence of Clearance Hinges on the Impact Dynamics Characteristics of Planar Mechanisms［J］. Vibration and Shock, 2017， 36(17)：74-78.
［14］姚伟达, 谢永诚. 模态叠加法在解间隙动力问题中的应用［C］∥第十届全国反应堆结构力学会议. 上海， 1998:398-401.
YAO Weida, XIE Yongcheng. Application of Modal Superposition Method in Solving Interstitial Dynamic Problems［C］∥The 10th National Conference on Reactor Structural Mechanics. Shanghai， 1998:398-401.
［15］王俊奇. 含间隙旋转副碰撞模型与应用研究［D］. 秦皇岛:燕山大学, 2018.
WANG Junqi. Research on the Collision Model and Application of Rotating Pair with Clearance［D］. Qinhuangdao:Yanshan University, 2018.

[1]	王成志, 王云超. 含运动副间隙的空间转向机构运动精度分析及优化设计#br#[J]. 中国机械工程, 2021, 32(09): 1027-1034,1042.
[2]	孔骏成;李菊;沈惠平. 2-RPaRSS并联操作手运动副间隙误差分析及补偿[J]. 中国机械工程, 2020, 31(06): 706-713.

考虑时变间隙的并联指向机构非线性模态分析

Nonlinear Modal Analysis of Parallel Pointing Mechanisms Considering Time-varying Clearances

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 2

编辑推荐

Metrics