基于流体自激的磨料水射流加工仿真与实验

doi:10.3969/j.issn.1004-132X.2022.03.004

中国机械工程 ›› 2022, Vol. 33 ›› Issue (03): 279-289.DOI: 10.3969/j.issn.1004-132X.2022.03.004

基于流体自激的磨料水射流加工仿真与实验

邓乾发1，2;汪杨笑1，2;袁巨龙1，2;吕冰海1，2;赵天晨3;王旭1，2

1.浙江工业大学超精密加工研究中心，杭州，310023
2.浙江工业大学特种装备制造与先进加工技术教育部重点实验室，杭州，310023
3.衢州学院机械工程学院，衢州，324000

出版日期:2022-02-10 发布日期:2022-02-21
作者简介:邓乾发，男，1972年生，副研究员。研究方向为超精密加工技术与智能装备。发表论文 60余篇，获发明专利授权20余项。E-mail:qfdeng@zjut.edu.cn。
基金资助:
国家自然科学基金（51775511,U1809221,51805485,U1604254）；
浙江省自然科学基金(LY17E050022，LR17E050002，LGG19E050006，LY21E050010)

Simulations and Experiments on Abrasive Water Jet Machining Based on Fluid Self-excitation

DENG Qianfa1，2;WANG Yangxiao1，2;YUAN Julong1，2;LYU Binghai1，2;ZHAO Tianchen3;WANG Xu1，2

1.Ultra-Precision Machining Center,Zhejiang University of Technology,Hangzhou,310023
2.Key Laboratory of Special Purpose Equipment and Advanced Processing Technology of Ministry of Education,Zhejiang University of Technology,Hangzhou,310023
3.College of Mechanical Engineering,Quzhou University,Quzhou,Zhejiang,324000

Online:2022-02-10 Published:2022-02-21

摘要/Abstract

摘要： 针对先进陶瓷材料的高效、精密加工，提出了一种基于流体自激的新型磨料水射流加工方法——自激振荡磨料水射流加工(SEO-AWJM)。采用ANSYS Fluent大涡模拟模型进行了流体仿真，仿真结果表明：当入口流速为135 m/s，腔长为4 mm时，下游喷嘴出口脉冲率最大达到28.47%。射流束的脉冲特性使得工件表面停滞层周期性变化，从而获得更高的峰值壁面剪切力，且该力在工件表面往复移动。通过SEO-AWJM实验，调节腔室长度获得最佳流体自激效果并对氮化硅基片进行加工。实验结果表明：定点加工10 min，使用磨料水射流加工去除最大深度为7.5 μm，使用SEO-AWJM去除最大深度为9.4 μm。初始表面粗糙度Ra为108.9 nm，磨料水射流加工6次后，Ra达到稳定值47.9 nm，SEO-AWJM加工4次后，Ra达到稳定值51.3 nm。

关键词: 自激振荡, 磨料射流, 加工, 陶瓷

Abstract: To precisely machine advanced ceramics with enhanced machining efficiency, a new type of water jet machining method was proposed based on fluid self-excitation, termed self-excited oscillating abrasive water jet machining(SEO-AWJM). ANSYS Fluents large eddy simulation model was used for fluid simulation. Simulation results show that with the inlet velocity of 135 m/s and the cavity length of 4 mm, the downstream nozzle outlet pulse rate reaches a maximum of 28.47%. The pulse characteristics of the jet beam cause periodically changes of stagnant layer of workpiece surfaces. Thereby a higher peak wall shear force was obtained and the force reciprocated on workpiece surfaces. SEO-AWJM experiments were conducted, the length of the chamber was adjusted to obtain the best fluid self-excited effectiveness, and silicon nitride substrate was processed. Experimental results show that after 10min fixed-point machining, the maximum removed depth is as 7.5 μm with abrasive water jet machining(AWJM)，while it is as 9.4 μm with SEO-AWJM. The initial surface roughness value Ra was 108.9 nm. After 6 times of AWJM, Ra reaches a stable value of 47.9 nm, after 4 times of SEO-AWJM, Ra reaches a stable value of 51.3 nm.

Key words: self-excited oscillating, abrasive jet, machining, ceramics

中图分类号:

TH161

邓乾发, 汪杨笑, 袁巨龙, 吕冰海, 赵天晨, 王旭, . 基于流体自激的磨料水射流加工仿真与实验[J]. 中国机械工程, 2022, 33(03): 279-289.

DENG Qianfa, WANG Yangxiao, YUAN Julong, LYU Binghai, ZHAO Tianchen, WANG Xu, . Simulations and Experiments on Abrasive Water Jet Machining Based on Fluid Self-excitation[J]. China Mechanical Engineering, 2022, 33(03): 279-289.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2022.03.004

http://www.cmemo.org.cn/CN/Y2022/V33/I03/279

参考文献

［1］HUANG C Z, WANG J, FENG Y X, et al. Recent Development of Abrasive Water Jet Machining Technology［J］. Key Engineering Materials, 2006, 315/316:396-400.
［2］王明波,王瑞和.湍流对磨料水射流中磨料颗粒受力的影响［J］.中国机械工程,2012,23(8):972-974.
WANG Mingbo, WANG Ruihe. Effects of Turbulence on Drag Force of Abrasive Water Jetting［J］.China Mechanical Engineering, 2012, 23(8):972-974.
［3］ZHU H T, HUANG C Z, WANG J, et al. Experimental Study on Abrasive Waterjet Polishing for Hard-brittle Materials［J］. International Journal of Machine Tools& Manufacture, 2009, 49(7/8):569-578.
［4］CHE C, HUANG C, WANG J, et al. Theoretical Model of Surface Roughness for Polishing Super Hard Materials with Abrasive Waterjet［J］. Key Engineering Materials, 2008, 375/376:465-469.
［5］LIU Z W, HUANG C Z, WANG J, et al. Study on Machining System of Precision Micro Abrasive Water Jet and Polish Experiment［J］. Key Engineering Materials, 2010, 431/432:102-105.
［6］WANG C J, CHEUNG C F, HO L T, et al. A Novel Multi-jet Polishing Process and Tool for High-efficiency Polishing［J］. International Journal of Machine Tools and Manufacture, 2017, 115:60-73.
［7］LYU Z, HUANG C Z, ZHU H T, et al. A 3D Simulation of the Fluid Field at the Jet Impinging Zone in Ultrasonic-assisted Abrasive Waterjet Polishing［J］. International Journal of Advanced Manufacturing Technology, 2016, 87:3091-3103.
［8］HOU R G, HUANG C Z, ZHU H T. Experimental Study on Pulsation Behavior of the Ultrasonic Vibration-assisted Abrasive Waterjet［J］. International Journal of Advanced Manufacturing Techno-logy, 2017,91:3851-3859.
［9］ROCKWELL D, NAUDASCHER E. Review-self-sustaining Oscillations of Flow Past Cavities［J］. Journal of Fluids Engineering, 1978, 100(2):152-165.
［10］汪朝晖, 饶长健, 高全杰,等. 基于瞬时涡量助推效应的自激振荡腔室脉动研究［J］. 机械工程学报, 2018, 54(14):207-214.
WANG Zhaohui, RAO Changjian, GAO Quanjie, et al. Study on the Pulsation of Self-excited Oscillation Chamber Based on Instantaneous Vortex Boosting Effect［J］. Journal of Mechanical Engineering, 2018, 54(14):207-214.
［11］FANG Z, ZENG F, XIONG T, et al. Large Eddy Simulation of Self-excited Oscillation Inside Helmholtz Oscillator［J］. International Journal of Multiphase Flow, 2020, 126:103253.
［12］裴江红,廖振方,唐川林.自激振荡脉冲射流频率特性实验研究［J］.中国机械工程,2009,20(1):60-63.
PEI Jianghong, LIAO Zhenfang, TANG Chuanlin. Experimental Study on Characteristics of Self-excited Oscillation Pulsed Water Jet［J］. China Mechanical Engineering, 2009, 20(1):60-63.
［13］TANG C L, HU D, ZHANG F H. Study on the Frequency Characteristic of Self-excited Oscillation Pulsed Water Jet［J］. Advanced Materials Research, 2011, 317/319:1456-1461.
［14］TANG C L, PEI J, HU D, et al. Erosion Experiment of Self-excited Oscillation Pulsed Jet［J］. Advanced Materials Research, 2014, 937:614-619.
［15］马飞,蔡腾飞,柳靖,等.自振射流频率特性的试验研究［J］.机械工程学报,2016,52(14):182-187.
MA Fei, CAI Tengfei, LIU Jing, et al. Experimental Study of Self Resonating Water Jet Frequency Characteristics［J］. Journal of Mechanical Engineering, 2016, 52(14):182-187.
［16］LI D, KANG Y, DING X, et al. Effects of Area Discontinuity at Nozzle Inlet on the Characteristics of High Speed Self-excited Oscillation Pulsed Waterjets［J］. Experimental Thermal&Fluidence, 2016, 79:254-265.
［17］HUANG M, KANG Y, WANG X, et al. Experimental Investigation on the Impingement Characteristics of a Self-excited Oscillation Pulsed Supercritical Carbon Dioxide Jet［J］. Experimental Thermal and Fluid Science, 2018, 94:304-315.
［18］王星, 徐琴, 张勇, 等. 纳米胶体自激脉冲空化射流抛光技术［J］. 光学精密工程, 2018, 26(9):168-177.
WANG Xing, XU Qin, ZHANG Yong, et al. Nanoparticle Colloid Self-induced Pulsed Cavitation Jet Polishing［J］.Optics and Precision Engineering, 2018, 26(9):168-177.
［19］邓乾发,郭晨曦,袁巨龙,等.基于自激振荡脉冲特性的磨粒流抛光不锈钢细管内壁的仿真与实验研究［J］.表面技术,2019,48(10):363-371.
DENG Qianfa, GUO Chenxi, YUAN Julong, et al. Simulation and Experimental Study on Abrasive Flow Polishing of Stainless Steel Tube Inner Wall Based on the Characteristics of Self-excited Oscillation Pulse［J］. Surface Technology, 2019,48(10):363-371.
［20］张成光, 张勇, 张飞虎,等. 新型后混合式磨料水射流系统的研制［J］. 机械工程学报, 2015, 51(5):205-212.
ZHANG Chengguang, ZHANG Yong, ZHANG Feihu, et al. Development of New Entrainment Abrasive Waterjet System ［J］. Journal of Mechanical Engineering, 2015, 51(5):205-212.
［21］MOREL T. Experimental Study of a Jet-driven Helmholtz Oscillator［J］. Journal of Fluids Engineering, 1979,101(3):383-390.
［22］ZHU H T, HUANG C Z, WANG J, et al. Theoretical Analysis on the Machining Mechanism in Ultrasonic Vibration Abrasive Waterjet［J］. Key Engineering Materials, 2006, 315/316:127-130.
［23］卢义玉,李晓红,王建生.自激振荡磨料射流中的磨料加速机理［J］.水动力学研究与进展(A辑),2003(2):205-208.
LU Yiyu, LI Xiaohong, WANG Jiansheng. Abrasive Accelerated Mechanisms in the Self-oscillating Abrasive Water Jet［J］. Chinese Journal of Hydrodynamics,2003(2):205-208.

[1]	张金阳, 许伟春, 王笑含, 江小辉, 高山. 铣削工艺优化对镍基高温合金加工残余应力分布影响研究[J]. 中国机械工程, 2024, 35(04): 624-635.
[2]	魏书鹏, 唐红涛, 李西兴, 杨冠宇, 张健. 考虑双资源约束的柔性机械加工车间逆调度问题研究[J]. 中国机械工程, 2024, 35(03): 457-471.
[3]	彭子伟, 王寅成, 杨力, 樊自田. 三头挤出成形氧化铝基陶瓷的精度研究[J]. 中国机械工程, 2024, 35(03): 481-486.
[4]	包锐, 刘阔, 张杰, 韩灵生, 李建明, 左月帅, 刘海波, 王永青. 聚碳酸酯超低温冷却车削表面形貌试验研究[J]. 中国机械工程, 2024, 35(02): 201-207.
[5]	杜煦, 常泽鑫, 郑军强, 任鹏飞. 一种考虑关节跃度约束的实时刀具路径光顺算法[J]. 中国机械工程, 2024, 35(02): 280-286.
[6]	黄云, 黄建超, 肖贵坚, 刘帅, 林瓯川, 刘振扬. 超疏水表面加工技术及耐磨性能研究进展[J]. 中国机械工程, 2024, 35(01): 2-26.
[7]	郑倩, 张亚欧, 高强, 卢军成, 杨翔钧, 赵万生, . 基于硼酸溶液的电火花加工机理分析及实验研究[J]. 中国机械工程, 2023, 34(24): 2936-2945.
[8]	李小睿, 赵威, 李浩, 史卫奇, 何宁. 高压低温CO2射流冷却条件下高速车削淬硬轴承钢的试验研究[J]. 中国机械工程, 2023, 34(24): 2975-2985.
[9]	严丁虎, 赵建社, 张昌昊, 高伟正, 朱寅, . 阵列变截面球槽结构电解加工流场设计及试验研究[J]. 中国机械工程, 2023, 34(23): 2824-2831.
[10]	贾志新, 张凯悦, 王津. 聚晶金刚石的混铁粉电火花加工方法研究[J]. 中国机械工程, 2023, 34(22): 2684-2692.
[11]	白小帆, 刘志强, 刘彦士. 轴向低频振动对皮质骨钻削进给力的影响试验与分析[J]. 中国机械工程, 2023, 34(20): 2411-2427.
[12]	卢耀安, 丘洪键, 王成勇, . 基于关键刀轴矢量插值的球头铣刀五轴加工光顺刀轴矢量生成方法[J]. 中国机械工程, 2023, 34(20): 2466-2474.
[13]	马预谱, 魏涛, 王力, 赵俊熠, 张鑫磊, 陈妮, 李亮, 何宁. 氮化铝基板嵌入式微流道设计及激光刻蚀研究[J]. 中国机械工程, 2023, 34(20): 2496-2503.
[14]	韩锐, 李秀红, 王嘉明, 李文辉, 程思源, 杨胜强, . 水平强制振动光整加工对TC4钛合金表面完整性参数的影响[J]. 中国机械工程, 2023, 34(17): 2037-2047.
[15]	史丽晨, 张倩, 刘腾飞, 刘亚雄, 卢竹青. 基于过程阻尼的钛合金丝材表面车削精整加工稳定性研究[J]. 中国机械工程, 2023, 34(16): 1936-1945.

基于流体自激的磨料水射流加工仿真与实验

Simulations and Experiments on Abrasive Water Jet Machining Based on Fluid Self-excitation

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics