含间隙关节的双推杆机械臂运动特性研究

doi:10.3969/j.issn.1004-132X.2022.11.007

中国机械工程 ›› 2022, Vol. 33 ›› Issue (11): 1309-1316.DOI: 10.3969/j.issn.1004-132X.2022.11.007

含间隙关节的双推杆机械臂运动特性研究

赵富强1,2;李钊钰1;高智颖1;吴红庆1;牛志刚2

1.太原科技大学重型机械教育部工程研究中心，太原，030024
2.太原理工大学极地工程与装备研究院，太原，030024

出版日期:2022-06-10 发布日期:2022-07-01
通讯作者: 李钊钰（通信作者），男，1996年生，硕士研究生。研究方向为机器人运动误差。E-mail：1445961920@qq.com。
作者简介:赵富强，男，1981年生，副教授。研究方向为机构与汽车动力学、新能源车辆等。E-mail：zfqgear@163.com。
基金资助:
山西省自然科学基金重点项目（201901D111009ZD）；山西省科技计划揭榜招标项目（20201101020）

Study on Motion Characteristics of Double Push Rod Manipulators with Joint Clearances

ZHAO Fuqiang1,2;LI Zhaoyu1;GAO Zhiying1;WU Hongqing1;NIU Zhigang2

1.Heavy Machinery Engineering Research Center of the Ministry of Education,Taiyuan University of Science and Technology，Taiyuan，030024
2.Institute of Polar Engineering and Equipment,Taiyuan University of Technology，Taiyuan，030024

Online:2022-06-10 Published:2022-07-01

摘要/Abstract

摘要： 建立了间隙关节的数学模型和含间隙关节的双推杆机械臂运动学模型；利用仿真模拟分析了单间隙关节A、单间隙关节B、双间隙关节A和B三种不同间隙关节位置和数量对机械臂末端轨迹、速度和加速度的影响，并采用绝对误差作为评价指标对影响程度进行了定量分析；搭建实验台对仿真结果进行了实验验证。结果表明，间隙关节导致机械臂末端运动轨迹在X轴和Y轴方向产生误差，且双间隙关节A和B造成的轨迹误差近似为两个单间隙关节的轨迹误差之和；机械臂末端速度和加速度曲线因间隙的存在而产生脉冲波动，其中单间隙关节A和单间隙关节B对曲线的影响程度相当，双间隙关节A和B在耦合作用下对曲线的影响程度远大于单间隙关节的影响程度。

关键词: 间隙关节, 双推杆机械臂, 运动特性, 平均绝对误差

Abstract: A mathematical model of the joint clearances and the kinematic model of the double push rod manipulators with joint clearances were established. The influences of the position and number of three different joint clearances including single joint clearance A, single joint clearance B, double joint clearance A and B on the trajectory, velocity and acceleration of the ends of the manipulators were analyzed by using simulation, and the absolute errors were used as the evaluation index to quantitatively analyze the influence degree. An experimental platform was built to verify the simulation results. The results show that, joint clearances lead to errors in the X-axis and Y-axis directions of the end motion trajectories of the manipulators, and the track errors caused by double joint clearance A and B are approximately the sum of the track errors of two single joint clearances. The velocity and acceleration curves at the ends of the manipulators are pulse fluctuations due to the existence of clearances. The influence degree of single joint clearances A and single joint clearances B on the curve is similar, and the influence degree of double joint clearances A and B on the curve under coupling is much greater than that of single joint clearances.

Key words: joint clearance, double push rod manipulator, motion characteristics, mean absolute error

中图分类号:

TP242

赵富强, 李钊钰, 高智颖, 吴红庆, 牛志刚. 含间隙关节的双推杆机械臂运动特性研究[J]. 中国机械工程, 2022, 33(11): 1309-1316.

ZHAO Fuqiang, LI Zhaoyu, GAO Zhiying, WU Hongqing, NIU Zhigang. Study on Motion Characteristics of Double Push Rod Manipulators with Joint Clearances[J]. China Mechanical Engineering, 2022, 33(11): 1309-1316.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2022.11.007

http://www.cmemo.org.cn/CN/Y2022/V33/I11/1309

参考文献

［1］WANG X, LIU G, MA S, et al. Effects of Restitution Coefficient and Material Characteristics on Dynamic Response of Planar Multi-body Systems with Revolute Joint Clearance［J］. Journal of Mechanical Science & Technology, 2017, 31(2):587-597.
［2］TAN H, HU Y, LI L. Effect of Friction on the Dynamic Analysis of Slider-crank Mechanism with Joint Clearance［J］. International Journal of Non-linear Mechanics, 2019, 115:20-40.
［3］TING K L, HSU K L, YU Z, et al. Clearance-induced Output Position Uncertainty of Planar Linkages with Revolute and Prismatic Joints［J］. Mechanism & Machine Theory, 2017, 111:66-75.
［4］SUN D, SHI Y, ZHANG B. Dynamic Analysis of Planar Mechanisms with Fuzzy Joint Clearance and Random Geometry［J］. Journal of Mechanical Design, 2018, 141(4):042301.
［5］FLORES P, MACHADO M, SILVA M T, et al. On the Continuous Contact Force Models for Soft Materials in Multibody Dynamics［J］. Multibody System Dynamics, 2011, 25(3):357-375.
［6］FLORES P, AMBRSIO J, CLARO J , et al. A Study on Dynamics of Mechanical Systems Including Joints with Clearance and Lubrication［J］. Mechanism & Machine Theory, 2006, 41(3):247-261.
［7］张义民, 黄贤振, 张旭方,等. 含运动副间隙平面机构位姿误差分析［J］. 东北大学学报(自然科学版), 2008, 29(8):1147-1150.
ZHANG Yiming，HUANG Xianzhen，ZHANG Xufang, et al. Pose Error Analysis of Planar Mechanism with Joint Clearance［J］. Journal of Northeastern University(Natural Science), 2008, 29(8):1147-1150.
［8］张志雄, 江志新, 杨拥民,等. 关节对中误差对机械臂末端定位精度影响［J］. 国防科技大学学报, 2014, 36(6):185-190.
ZHANG Zhixiong，JIANG Zhixin，YANG Yongmin, et al. Joint Clearance Effects on Robot Manipulators Positional Error［J］. Journal of National University of Defense Technology, 2014, 36(6):185-190.
［9］邓培生, 原大宁, 刘宏昭,等. 考虑杆件柔性的间隙机构系统磨损分析［J］. 中国机械工程, 2016, 27(2):143-149.
DENG Peisheng，YUAN Daning，LIU Hongzhao，et al. Wear Analysis on Intermittent Mechanism Systems Including Flexible Bar［J］. China Mechanical Engineering, 2016, 27(2):143-149.
［10］ERKAYA S, DOGN S，SEFKATLIOGLU E. Analysis of the Joint Clearance Effects on a Compliant Spatial Mechanism［J］. Mechanism and Machine Theory, 2016, 104:255-273.
［11］ERKAYA S, UZMAY I. Modeling and Simulation of Joint Clearance Effects on Mechanisms Having Rigid and Flexible Links［J］. Journal of Mechanical Science & Technology, 2014, 28(8):2979-2986.
［12］王见, 董虎, 王兆东,等. 含关节间隙的3-CPaRR解耦并联机构弹性动力学建模与分析［J］. 振动与冲击, 2020, 39(5):118-130.
WANG Jian，DONG Hu，WANG Zhaodong，et al. Elastic Dynamic Modeling and Analysis for a 3-CPaRR Decoupled Parallel Mechanism with Joint Clearance［J］. Journal of Vibration and Shock, 2020, 39(5):118-130.
［13］ZHANG X , ZHANG X . A Comparative Study of Planar 3-RRR and 4-RRR Mechanisms with Joint Clearances［J］. Robotics & Computer Intergrated Manufacturing, 2016, 40:24-33.
［14］WANG X, LIN W, JI X, et al. Dynamic Analysis of a Planar Multibody System with Multiple Revolute Joint Clearances［J］. ARCHIVE Proceedings of the Institution of Mechanical Engineers Part C:Journal of Mechanical Engineering Science, 2018, 203/210:1989-1996.
［15］彭京徽, 张弘弨, 朱孝磊,等. 摆弹机构运动特性与误差分析［J］. 兵器装备工程学, 2020, 41(4):97-100.
PENG Jinghui，ZHANG Hongchao，ZHU Xiaolei, et al. Motion Characteristics and Error Analysis of Shell Swinging Service Mechanism［J］. Journal of Ordnance Equipment Engineering, 2020, 41 (4):97-100.
［16］ZHAO F Q, DU P Y, HUANG Q X, et al. Giant Six-legged Polar Research Vehicle with Tracked Feet:US20200216125A1［P］. 2020-07-09.

[1]	张国兴1;侯雨雷1;曾达幸1;窦玉超2;段艳宾2. 四自由度混联天线机构运动特性分析[J]. 中国机械工程, 2020, 31(21): 2566-2572.
[2]	林超1;夏锡光1;邢庆坤2;刘文思1. 非圆齿轮型间歇转动机构的设计与运动特性分析[J]. 中国机械工程, 2020, 31(10): 1142-1148.
[3]	李强, 巩亚东, 宋伟刚. 基于物料运动特性的旋回破碎机生产率分析[J]. 中国机械工程, 2016, 27(15): 2034-2039.
[4]	贾先, 赵升吨, 范淑琴, 谭栓斌. 双动压力机用压边滑块串联四连杆工作机构的优化[J]. 中国机械工程, 2016, 27(09): 1223-1228.
[5]	陈科, 殷磊, 郭伟, 张建中, . 基于投影几何法的虎克万向节轴承的运动特性分析[J]. 中国机械工程, 2016, 27(06): 732-736.
[6]	周香琴. 球面4R机构运动特性研究及其应用探索 [J]. 中国机械工程, 2011, 22(2): 153-158.
[7]	张伯平, 王伟, 刘焜. 颗粒介质双筒剪切单元摩擦阻力的研究 [J]. 中国机械工程, 2011, 22(15): 1832-1836.

含间隙关节的双推杆机械臂运动特性研究

Study on Motion Characteristics of Double Push Rod Manipulators with Joint Clearances

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 7

编辑推荐

Metrics