磨粒流加工壁面效应研究

doi:10.3969/j.issn.1004-132X.2023.09.008

中国机械工程 ›› 2023, Vol. 34 ›› Issue (09): 1077-1085.DOI: 10.3969/j.issn.1004-132X.2023.09.008

磨粒流加工壁面效应研究

汤炉滨1,2;文东辉1,2;孔凡志1,2;袁巧玲1,2

1.特种装备制造与先进加工技术教育部/浙江省重点实验室，杭州，310023
2.浙江工业大学机械工程学院，杭州，310023

出版日期:2023-05-10 发布日期:2023-05-29
通讯作者: 孔凡志（通信作者），男，1976年生，副教授。研究方向为超精密加工。E-mail:franzkong@zjut.edu.cn。
作者简介:汤炉滨，男，1998年生，硕士研究生。研究方向为超精密加工。
基金资助:
浙江省科技计划(2021C01G6232927)；浙江省公益技术应用研究项目(LGG22E050033)

Research on Wall Effect of Abrasive Flow Machining

TANG Lubin1,2;WEN Donghui1,2;KONG Fanzhi1,2;YUAN Qiaoling1,2

1.Special Equipment Manufacturing and Advanced Processing Technology, Ministry of Education/Zhejiang Provincial Key Laboratory,Hangzhou,310023
2.School of Mechanical Engineering,Zhejiang University of Technology,Hangzhou,310023

Online:2023-05-10 Published:2023-05-29

摘要/Abstract

摘要： 数值模拟了圆柱内表面的初始粗糙度、入口流速和内孔直径对壁面流场压力、局部压差及剪切力的影响规律，分析了入口处流场速度和剪切力的形成过程，从磨粒切削作用角度剖析了圆柱内表面入口处过抛现象的形成原因，结合磨粒流加工试验揭示了各参数对壁面效应的影响规律。理论分析和试验结果表明：增大圆孔直径或减小入口流速能有效改善磨粒流流场压力的均匀性，初始表面粗糙度对流场压力数值及其局部压差有微弱影响；入口处圆孔壁面速度突变引起剪切力突变，从而导致磨粒流加工过抛现象；初始表面粗糙度Ra=0.296 μm时有利于减弱磨粒流加工的壁面效应，而Ra=4.273 μm时有利于提高材料去除速率。

关键词: 流场压力, 剪切力, 壁面效应, 过抛现象

Abstract: Effects of initial surface roughness, inlet flow velocity and hole diameter on flow field pressure, local pressure difference and shear force of cylinder inner wall were simulated by numerical method. Formation processes of flow field velocity and shear force at the cylinder entrance were detected, then over-polishing phenomenon accrued at the entrance of cylinder inner surfaces was deduced according to the abrasive forces action. Effects of all parameters on wall effect during abrasive flow machining was revealed by abrasive flow machining experiments and simulation. Theoretical analysis and experimental results show that, increasing diameter of round hole or reducing inlet flow rate may improve pressure uniformity of abrasive flow field effectively, initial surface roughness has a weak effect on flow field pressure value and the local pressure difference. Sharp transition of wall surface velocity at the entrance causes a sudden change of shear force, then leads to over-polishing phenomenon of abrasive flow machining. Initial surface roughness Ra=0.296 μm is conducive to weakening wall effect of abrasive flow machining and Ra=4.273 μm is conducive to increasing material removal rate.

Key words: , flow field pressure, shear force, wall effect, over-polishing phenomenon

中图分类号:

TG580

汤炉滨, 文东辉, 孔凡志, 袁巧玲, . 磨粒流加工壁面效应研究[J]. 中国机械工程, 2023, 34(09): 1077-1085.

TANG Lubin, WEN Donghui, KONG Fanzhi, YUAN Qiaoling, . Research on Wall Effect of Abrasive Flow Machining[J]. China Mechanical Engineering, 2023, 34(09): 1077-1085.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2023.09.008

http://www.cmemo.org.cn/CN/Y2023/V34/I09/1077

参考文献

［1］CHEUNG C F, WANG C J, CAO Z C, et al. Development of a Multi-jet Polishing Process for Inner Surface Finishing［J］. Precision Engineering, 2018, 52:112-121.
［2］焦悦, 贺斌, 李朋, 等. 大深径比微孔加工技术及其发展［J］. 航空科学技术, 2018, 29(3):1-7.
JIAO Yue, HE Bin, LI Peng, et al. Large Depth Diameter Microporous Processing Technology and Its Development［J］. Aviation Science and Technology, 2018, 29(3):1-7.
［3］ANTUNES R A, SALADOR C A F, OLIVEIRA M C L. Materials Selection of Optimized Titanium Alloys for Aircraft Applications［J］. Materials Research, 2018, 21(2):e20170979.
［4］刘薇娜,蔡智杰,李云峰,等.喷油嘴微孔磨粒流抛光数值模拟与试验［J］.中国机械工程,2017, 28(1):13-19.
LIU Weina, CAI Zhijie, LI Yunfeng, et al. Numerical Simulation and Experiment of Microporous Abrasive Flow Polishing of Fuel Injector［J］. China Mechanical Engineering, 2017, 28(1):13-19.
［5］BARAIYA R, BABBAR A, JAIN V, et al. In-situ Simultaneous Surface Finishing Using Abrasive Flow Machining via Novel Fixture［J］. Journal of Manufacturing Processes, 2020, 50:266-278.
［6］李俊烨, 朱志宝, 张心明, 等.异形截面孔磨粒流精密加工质量分析［J］.中国机械工程,2021, 32(17):2063-2073.
LI Junye, ZHU Zhibao, ZHANG Xinming, et al. Quality Analysis of Abrasive Flow Precision Machining of Special-shaped Section Holes［J］. China Mechanical Engineering, 2021, 32(17):2063-2073.
［7］李琛, 计时鸣, 谭大鹏, 等.软性磨粒流加工特性及近壁区域微切削机理［J］.机械工程学报,2014, 50(9):161-168.
LI Chen, JI Shiming, TAN Dapeng, et al. Microcarpiece Processing Characteristics and Near Wall Region of Soft Abrasives［J］. Journal of Mechanical Engineering, 2014, 50(9):161-168.
［8］SINGH H, SANKAR M R, JAIN V K. Simulation and Experimental Investigations into Abrasive Flow Nanofinishing of Surgical Stainless Steel Tubes［J］. Machining Science and Technology, 2018, 22(3):454-475.
［9］AZAMI A, AZIZI A, KHOSHANJAM A, et al. A New Approach for Nanofinishing of Complicated-surfaces Using Rotational Abrasive Finishing Process［J］. Materials and Manufacturing Processes, 2020, 35(8):940-950.
［10］SHARMA A K, VENKATESH G, RAJESHA S, et al. Experimental Investigations into Ultrasonic-assisted Abrasive Flow Machining(UAAFM) Process［J］. The International Journal of Advanced Manufacturing Technology, 2015, 80(1/4):477-493.
［11］WANG A C, CHENG K C, CHEN K Y, et al. A Study on the Abrasive Gels and the Application of Abrasive Flow Machining in Complex-hole Polishing［J］. Procedia CIRP, 2018, 68:523-528.
［12］高航, 付有志, 王宣平, 等.螺旋面磨料流光整加工仿真与试验［J］.浙江大学学报(工学版), 2016, 50(05):920-926.
GAO Hang, FU Youzhi, WANG Xuanping, et al. Simplified Assembly and Test Simulation and Test［J］. Journal of Zhejiang University(Engineering Edition), 2016, 50(5):920-926.
［13］李研彪, 陈强, 张利.钛合金薄壁曲面液态金属-磨粒流加工仿真与试验研究［J］.机械工程学报,2021, 57(23):220-231.
LI Yanbiao, CHEN Qiang, ZHANG Li. Simulation and Experimental Research on Liquid Metal-abrasive Flow Machining of Titanium Alloy Thin-walled Surfaces［J］. Journal of Mechanical Engineering, 2021, 57(23):220-231.
［14］尹洪超, 刘宵, 翟镇德, 等. 多角度弯曲管磨粒流加工数值模拟研究［J］. 中国机械工程, 2021, 32(11):1299-1306.
YIN Hongchao, LIU Xiao, ZHAI Zhende, et al. Numerical Simulation of Multi-angle Bending Tube Grain Flow［J］. China Mechanical Engineering, 2021,32(11):1299-1306.
［15］张克华, 许永超, 丁金福, 等.异形内孔曲面的磨料流均匀加工方法研究［J］. 中国机械工程, 2013, 24(17):2377-2382.
ZHANG Kehua, XU Yongchao, DING Jinfu, et al. Research on Abrasive Flow Uniform Machining Method of Special-shaped Inner Hole Surface［J］.China Mechanical Engineering, 2013, 24(17):2377-2382.
［16］兰文涛, 吴爱祥.非牛顿流体管道流动方程及其近似解［J］. 哈尔滨工业大学学报, 2020, 52(12):140-146.
LAN Wentao, WU Aixiang. Non-Newtonian Fluid Pipeline Flow Equation and Its Approximate Solution［J］. Journal of Harbin Institute of Technology, 2020, 52(12):140-146.
［17］计时鸣, 李琛, 谭大鹏, 等. 软性磨粒流加工方法及近壁区域特性［J］.浙江大学学报(工学版), 2012, 46(10):1764-1772.
JI Shiming, LI Chen, TAN Dapeng, et al. SoftAbrasive Flow Machining Method and Properties of Near-wall Region［J］. Journal of Zhejiang University(Engineering Science Edition), 2012, 46(10):1764-1772.
［18］刘宵, 尹洪超, 穆林. 基于欧拉-欧拉方法的细长管道内磨粒流加工数值模拟研究［J］. 大连理工大学学报, 2021, 61(2):143-150.
LIU Xiao, YIN Hongchao, MU Lin. Numerical Simulation of Waste Flow Processing in Employed Pipeline Based on Euler-Euler Method［J］. Journal of Dalian University of Science and Technology, 2021, 61(2):143-150.
［19］FU Youzhi, GAO Hang, YAN Qiusheng, et al. A New Predictive Method of the Finished Surface Profile in Abrasive Flow Machining Process［J］. Precision Engineering, 2019, 60:497-505.

[1]	祁瑁富, 孙远韬, 田春雷, 冯嘉琪. 基于正交试验的850吨冷剪机剪切失效机理分析及其优化设计[J]. 中国机械工程, 2024, 35(04): 752-759.
[2]	熊江茗, 周杰, 王时龙, 杨波, 王四宝, 董建鹏. 基于Johnson-Cook模型的不锈钢管剪切数值模拟[J]. 中国机械工程, 2020, 31(15): 1877-1884.

磨粒流加工壁面效应研究

Research on Wall Effect of Abrasive Flow Machining

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 2

编辑推荐

Metrics