电火花机械磨削修整粗粒度成形砂轮试验研究

doi:10.3969/j.issn.1004-132X.2023.10.005

中国机械工程 ›› 2023, Vol. 34 ›› Issue (10): 1164-1171.DOI: 10.3969/j.issn.1004-132X.2023.10.005

电火花机械磨削修整粗粒度成形砂轮试验研究

袁尚勇;陈根余;戴隆州;鲁恩昊

1.湖南大学机械与运载工程学院，长沙，410082
2.湖南大学激光研究所，长沙，410082

出版日期:2023-05-25 发布日期:2023-06-07
通讯作者: 陈根余（通信作者），男，1965年生，教授、博士研究生导师。研究方向为超硬磨料砂轮修整技术、激光微纳加工、电火花加工等。E-mail：hdgychen@163.com。
作者简介:袁尚勇，男，1998年生，硕士研究生。研究方向为超硬磨料砂轮修整技术、电火花磨削复合加工。E-mail：2325249496@qq.com。
基金资助:
广东省重点领域研发计划（2020B090924005）

Experimental Research of Coarse-grained Forming Grinding Wheel Dressed by EDDG

YUAN Shangyong;CHEN Genyu;DAI Longzhou;LU Enhao

1.College of Mechanical and Vehicle Engineering，Hunan University，Changsha，410082
2.Laser Research Institute of Hunan University，Hunan University，Changsha，410082

Online:2023-05-25 Published:2023-06-07

摘要/Abstract

摘要： 粗粒度金属基金刚石砂轮磨削效率高，面形精度保持性好，可以满足各种成形零件的精密加工，但存在因修整困难而难以推广的问题。针对该问题，提出采用电火花机械磨削法修整粗粒度金刚石砂轮。探究了放电参数对修整效率及刀具损耗量的影响规律，并以修整效率为优化目标选取粗修整试验放电参数，以修整精度为优化目标选取精修整试验放电参数。设计了半径为3 mm的凹圆弧、凸圆弧砂轮修整试验，粗修整后凹圆弧、凸圆弧半径分别为2867.510 μm、2919.254 μm，尺寸误差分别为4.43%、2.69%，轮廓精度PV值为54.34 μm；精修整后凹圆弧、凸圆弧半径分别为3005.107 μm、3001.588 μm，尺寸误差分别为0.17%、0.053%，轮廓精度PV值为17.28 μm。最后，磨削碳化硅陶瓷试件，获得凹圆弧、凸圆弧半径的尺寸误差分别为0.24%、0.045%，工件表面粗糙度Ra可达0.463 μm。

关键词: 电火花机械磨削, 金刚石砂轮, 粗粒度成形砂轮, 轮廓精度

Abstract: The coarse-grained metal bond diamond wheel had high grinding efficiency and good surface shape accuracy retention， which might meet the precision machining of various forming parts， but the difficulty of dressing maked it difficult to popularize. In order to solve this problem， the EDDG was proposed for coarse-grained diamond grinding wheel dressing. The influences of discharge parameters on dressing efficiency and tool loss were investigated. The discharge parameters of rough dressing were selected with the dressing efficiency as the optimization objective， and the discharge parameters of precision dressing were selected with the dressing accuracy as the optimization objective. The concave and convex arc-shaped wheels with design radius of 3 mm were used for dressing experiments. After rough dressing， the radius of concave and convex arc-shaped are as 2867.510 μm and 2919.254 μm respectively， the dimensional errors are as 4.43% and 2.69% respectively， and the PV value of profile accuracy is as 54.34 μm. After precision dressing， the radius of concave and convex arc-shaped are as 3005.107 μm and 3001.588 μm respectively， the dimensional errors are as 0.17% and 0.053% respectively， and the PV value of profile accuracy is as 17.28 μm. Finally， the dimensional errors of concave and convex arc-shaped obtained by grinding silicon carbide ceramic specimens are as 0.24% and 0.045% respectively， and the surface roughness value of the workpiece is as 0.463 μm.

Key words: , electrical discharge diamond grinding（EDDG）, diamond grinding wheel, coarse-grained forming wheel, profile accuracy

中图分类号:

TG743

袁尚勇, 陈根余, 戴隆州, 鲁恩昊. 电火花机械磨削修整粗粒度成形砂轮试验研究[J]. 中国机械工程, 2023, 34(10): 1164-1171.

YUAN Shangyong, CHEN Genyu, DAI Longzhou, LU Enhao. Experimental Research of Coarse-grained Forming Grinding Wheel Dressed by EDDG[J]. China Mechanical Engineering, 2023, 34(10): 1164-1171.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2023.10.005

http://www.cmemo.org.cn/CN/Y2023/V34/I10/1164

参考文献

［1］郭东明，孙玉文，贾振元. 高性能精密制造方法及其研究进展［J］. 机械工程学报， 2014， 50（11）：119-134.
GUO Dongming， SUN Yuwen， JIA Zhenyuan. Methods and Research Progress of High Performance Manufacturing［J］. Journal of Mechanical Engineering， 2014， 50（11）：119-134.
［2］赵清亮，赵玲玲，王宇，等. 电镀金刚石砂轮高效精密修整及熔融石英磨削试验研究［J］. 机械工程学报， 2013， 49（23）：174-181.
ZHAO Qingliang， ZHAO Lingling， WANG Yu， et al. High Efficient Precision Conditioning of the Electroplated Diamond Wheel and Grinding of Fused Silica Glasses［J］. Journal of Mechanical Engineering， 2013， 49（23）：174-181.
［3］DERKX J M， HOOGSTRATE A M， SAURWALT J J， et al. Form Crush Dressing of Diamond Grinding Wheels［J］. CIRP Annals—Manufacturing Technology， 2008， 57（1）：349-352.
［4］胡忠辉，袁哲俊. CBN砂轮修整方法及其对磨削表面完整性的影响［J］. 磨料磨具与磨削， 1992（3）：2-7.
HU Zhonghui， YUAN Zhejun. Surface Integrity. Ingrinding Influenced by Grinding Wheel Dressing Method［J］. Abrasives and Grinding， 1992（3）：2-7.
［5］OKUY AMA S， IWAYA T， KITAJIMA T， et al. Study on the Round off Truing Using the Circular Motion of CNC Grinding Machine［J］. Journal of the Japan Society for Precision Engineering， 1998， 64：1669-1673.
［6］KITZIG H， TAWAKOLI T， AZARHOUSHANG B. A Novel Ultrasonic-assisted Dressing Method of Electroplated Grinding Wheels via Stationary Diamond Dresser［J］. The International Journal of Advanced Manufacturing Technology， 2016， 86（1/4）：487-494.
［7］XIE X Z， CHEN G Y， LI L J. Dressing of Resin-bonded Superabrasive Grinding Wheels by Means of Acousto-optic Q-switched Pulsed Nd：YAG Laser［J］. Optics and Laser Technology， 2004， 36（5）：409-419.
［8］DENG H， CHEN G Y， ZHOU C， et al. Processing Parameter Optimization for the Laser Dressing of Bronze-bonded Diamond Wheels［J］. Applied Surface Science， 2014， 290：475-481.
［9］YUNG K C， CHEN G Y， LI L J. The Laser Dressing of Resin-bonded CBN Wheels by a Q-switched Nd：YAG Laser［J］. International Journal of Advanced Manufacturing Technology， 2003， 22（7/8）：541-546.
［10］DENG H， XU Z. Laser Dressing of Arc-shaped Resin-bonded Diamond Grinding Wheels［J］. Journal of Materials Processing Technology， 2021， 288：116884.
［11］SANCHEZ J A， ORTEGA N， LACALLE L， et al. Analysis of the Electro Discharge Dressing（EDD）Process of Large-grit Size CBN Grinding Wheels［J］. The International Journal of Advanced Manufacturing Technology， 2005， 29（7/8）：688-694.
［12］XIE J， TAMAKI J. An Experimental Study on Discharge Mediums Used for Electro-contact Discharge Dressing of Metal-bonded Diamond Grinding Wheel［J］. Journal of Materials Processing Technology， 2008， 208（1/3）：239-244.
［13］HE Q， XIE J， LU K， et al. Study on In-air Electro-contact Discharge（ECD）Truncating of Coarse Diamond Grinding Wheel for the Dry Smooth Grinding of Hardened Steel［J］. Journal of Materials Processing Technology， 2020， 276：116402.
［14］WANG Y， ZHOU X J， HU D J. An Experimental Investigation of Dry-electrical Discharge Assisted Truing and Dressing of Metal Bonded Diamond Wheel［J］. International Journal of Machine Tools & Manufacture， 2006， 46：333-342.
［15］SATYARTHI M K， PANDEY P M. Modeling of Material Removal Rate in Electric Discharge Grinding Process［J］. International Journal of Machine Tools & Manufacture， 2013， 74：65-73.
［16］RAO X S， ZHANG F H， LU Y J， et al. Surface and Subsurface Damage of Reaction-bonded Silicon Carbide Induced by Electrical Discharge Diamond Grinding［J］. International Journal of Machine Tools & Manufacture， 2020， 154：103564.
［17］KLINK A. Wire Electro Discharge Trueing and Dressing of Fine Grinding Wheels［J］. CIRP Annals—Manufacturing Technology， 2010， 59（1）：235-238.
［18］薛荣，顾琳，杨凯，等，喷雾电火花铣削加工的能量分配与材料蚀除模型［J］. 机械工程学报， 2012， 48（21）：175-182.
XUE Rong， GU Lin， YANG Kai， et al. Energy Distribution and Material Erosion Model in Near-dry Electrical Discharge Milling［J］. Journal of Mechanical Engineering， 2012， 48（21）：175-182.

[1]	鲁艳军, 关伟锋, 孙佳劲, 莫睿, 伍晓宇. 基于放电修锐的粗金刚石砂轮干式镜面磨削技术[J]. 中国机械工程, 2023, 34(09): 1052-1060.
[2]	李守港, 刘鹏, 刘祥, 胡志力, . 高强钢热冲压结构件三维激光切割回弹规律及精度补偿方法[J]. 中国机械工程, 2022, 33(22): 2741-2747.
[3]	陈根余, 戴隆州, 李明全, 袁尚勇. 激光与电火花复合修整粗粒度弧形金刚石砂轮试验研究[J]. 中国机械工程, 2022, 33(15): 1780-1786.
[4]	张鹏, 曹泽泽, 寇淑清, 王涛, 郭继保, 李金哲, 吴磊. 组合式凸轮轴径向滚花装配机理及连接强度研究[J]. 中国机械工程, 2022, 33(06): 664-671.
[5]	伍俏平, 邓朝晖, 赵前程, 潘占, 康辉民, 万林林, . 基于新型金刚石砂轮的Al2O3陶瓷磨削性能[J]. 中国机械工程, 2014, 25(16): 2240-2246.
[6]	张贝, 傅玉灿, 苏宏华. 单层钎焊金刚石砂轮的修整实验研究[J]. 中国机械工程, 2014, 25(13): 1778-1783.
[7]	陈建毅1, 徐西鹏2. 钎焊金刚石砂轮高速磨削氧化铝的磨削比能研究[J]. 中国机械工程, 2013, 24(07): 890-894.
[8]	詹友基, 李远, 黄辉, 徐西鹏. 钎焊金刚石砂轮磨削硬质合金的磨削力研究 [J]. 中国机械工程, 2010, 21(15): 1844-1849.
[9]	蔡兰蓉;贾妍;胡德金;. 电火花修整金刚石导电砂轮温度场分析和实验研究[J]. J4, 2008, 19(9): 0-1054.
[10]	王续跃;徐云飞;徐文骥;王连吉;康仁科;郭东明. 辅助侧向吹气法金刚石砂轮激光修锐试验与评价[J]. J4, 2008, 19(6): 0-750.
[11]	贾妍;蔡兰蓉;胡德金;. 表面放电辅助修整金属基金刚石砂轮的温度场分析和放电参数优化[J]. J4, 2008, 19(15): 0-1889.

电火花机械磨削修整粗粒度成形砂轮试验研究

Experimental Research of Coarse-grained Forming Grinding Wheel Dressed by EDDG

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 11

编辑推荐

Metrics