动力稳定作业参数对道床稳定性的影响

doi:10.3969/j.issn.1004-132X.2023.19.005

中国机械工程 ›› 2023, Vol. 34 ›› Issue (19): 2313-2319，2369.DOI: 10.3969/j.issn.1004-132X.2023.19.005

动力稳定作业参数对道床稳定性的影响

赵泽民;王立华;黄洪燚;陈太茂;蒋维

昆明理工大学机电工程学院，昆明，650500

出版日期:2023-10-10 发布日期:2023-11-02
通讯作者: 王立华（通信作者），男，1974年生，教授、博士研究生导师。研究方向为机械动力学、数字化设计与制造。发表论文100余篇。E-mail：kmwanglihua@163.com。
作者简介:赵泽民，男，1996年生，博士研究生。研究方向为机械动力学、动力稳定作业、轨枕-道床耦合特性分析。E-mail：bomen888@163.com。
基金资助:
国家自然科学基金（51765023）

Effects of Dynamic Stabilization Operation Parameters on Ballast Stability

ZHAO Zemin;WANG Lihua;HUANG Hongyi;CHEN Taimao;JIANG Wei

Faculty of Mechanical and Electrical Engineering,Kunming University of Science and Technology,Kunming,650500

Online:2023-10-10 Published:2023-11-02

摘要/Abstract

摘要： 为提高道床稳定性，采用离散元有限元耦合方法建立了动力稳定装置道床耦合模型。采用正交试验法，以动力稳定作业参数为研究对象，道床密实度和下沉量为评价指标，对作业参数进行了显著性与灵敏度分析。搭建了动力稳定装置试验台，验证了仿真模型的合理性。仿真和试验结果显示：动力稳定作业参数对道床稳定性的显著性影响关系为激振力幅值＞激振频率＞垂向下压力；动力稳定装置最优作业参数为激振频率35 Hz、激振力幅值197 kN。

关键词: 动力稳定作业, 正交试验, 道床稳定性, 离散元有限元耦合法

Abstract: To improve ballast stability, the dynamic stabilization unit-ballast coupling models were established using the discrete element-finite element coupling method. The orthogonal test method was used to analyze the significance and sensitivity of the operation parameters with the dynamic stabilization operation parameters as the research factors and the ballast compactness and settlement as the evaluation indexes. The dynamic stabilization unit test rig was built to verify the rationality of the simulation models. The simulation and experimental results show that the significant influences of dynamic stabilization operation parameters on ballasted are as follows: the effects of the amplitude of the excitation force are greater than that of the excitation frequency, and the effects of the excitation frequency are greater than that of the vertical downward pressure. The dynamic stabilization optimal operation parameters are as excitation frequency of 35 Hz and as excitation force amplitude of 197 kN.

Key words: dynamic stabilization operation, orthogonal test, ballast stability, discrete element-finite element coupling method

中图分类号:

U216

赵泽民, 王立华, 黄洪燚, 陈太茂, 蒋维. 动力稳定作业参数对道床稳定性的影响[J]. 中国机械工程, 2023, 34(19): 2313-2319，2369.

ZHAO Zemin, WANG Lihua, HUANG Hongyi, CHEN Taimao, JIANG Wei. Effects of Dynamic Stabilization Operation Parameters on Ballast Stability[J]. China Mechanical Engineering, 2023, 34(19): 2313-2319，2369.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2023.19.005

http://www.cmemo.org.cn/CN/Y2023/V34/I19/2313

参考文献

［1］GRABE P J, MAREE J S. Use of a Dynamic Track Stabiliser to Improve Track Maintenance and Optimisation of Track Tamping［C］∥Proceedings of the 6th International Heavy Haul Association Conference. Cape Town, 1997:945-957.
［2］JADIDIRENDI K, ZAKERI J A, TENG H H. Field Investigation for Identifying the Effects of Dynamic Track Stabilizing Operation on Track Geometrical Indices［C］∥IEEE Joint Rail Conference. California, 2015:1-8.
［3］王军，王立华，杨鑫岩. 动力稳定车稳定装置建模及参数优化［J］. 机械与电子，2015(11)：35-38.
WANG Jun, WANG Lihua, YANG Xinyan. Stabilizer Modeling and Parameter Optimization for Dynamic Stability Vehicles［J］. Machinery & Electronics, 2015(11):35-38.
［4］严波. 动力稳定车作业过程的动力学特性研究［D］. 昆明：昆明理工大学，2017.
YAN Bo. Research on Dynamic Mechanical Characteristics in the Operating Process of Dynamic Track Stabilizer［D］. Kunming：Kunming University of Science and Technology, 2017.
［5］SHI Shunwei, GAO Liang, HOU Bowen, et al. Numerical Investigation on Multiscale Mechanical Properties of Ballast Bed in Dynamic Stabilization Maintenance［J］. Computers and Geotechnics, 2022, 144:104649.
［6］WANG Lihua, ZHAO Zemin, WANG Jiongli, et al. Mechanical Characteristics of Ballast Bed under
Dynamic Stabilization Operation Based on Discrete Element and Experimental Approaches［J］. Shock and Vibration, 2021, 2021:1-11.
［7］DI RENZO A, DI MAIO F P. An Improved Integral Non-linear Model for the Contact of Particles in Distinct Element Simulations［J］. Chemical Engineering Science, 2005, 60(5):1303-1312.
［8］RAMREZ R, PSCHEL T, BRILLIANTOV N V, et al. Coefficient of Restitution of Colliding Viscoelastic Spheres［J］. Physical Review E, 1999, 60(4):4465-4472.
［9］徐旸，高亮，杨国涛，等. 道砟颗粒的精细化建模及对道床力学性能影响［J］. 铁道学报，2014，36(9)：73-78.
XU Yang,GAO Liang, YANG Guotao, et al. Fine Modelling of Ballast Grains and Influence on Mechanical Properties of Track Bed［J］. Journal of the China Railway Society, 2014, 36(9):73-78.
［10］XIAO Jieling, LIU Ganzhong, LIU Jianxing, et al. Parameters of a Discrete Element Ballasted Bed Model Based on a Response Surface Method［J］. Journal of Zhejiang University：Science A, 2019, 20(9):685-700.
［11］LI Linfeng, LIU Weifeng, MA Meng, et al. Research on the Dynamic Behaviour of the Railway Ballast Assembly Subject to the Low Loading Condition Based on a Tridimensional DEM-FDM Coupled Approach［J］. Construction and Building Materials, 2019, 218:135-149.
［12］SADEGHI J M, ZAKERI J A, NAJAR M. Developing Track Ballast Characteristic Guideline in Order to Evaluate Its Performance［J］. International Journal of Railway, 2016, 9(2):27-35.
［13］曾树谷. 铁路散粒体道床［M］. 北京：中国铁道出版社, 1997.
ZENG Shugu. Railway Ballast Bed［M］. Beijing:China Railway Publishing House, 1997.

[1]	祁瑁富, 孙远韬, 田春雷, 冯嘉琪. 基于正交试验的850吨冷剪机剪切失效机理分析及其优化设计[J]. 中国机械工程, 2024, 35(04): 752-759.
[2]	向柔潼, 王时龙, 周杰, 易力力. 辐照环境下新型气动位置传感器压力响应特性研究[J]. 中国机械工程, 2023, 34(11): 1364-1371.
[3]	陈俞鹏, 王海波, 薛朝军, 邹怀静, 高依民, . 工业装配抗振外骨骼的动力学仿真及试验研究[J]. 中国机械工程, 2023, 34(04): 404-413.
[4]	任振宝, 曹春平. 基于熵权综合评价法的动力电池壳首道次拉深成形参数优化[J]. 中国机械工程, 2022, 33(13): 1622-1628.
[5]	高建平, 余佳衡, 孟垚, 郗建国. 电动车辆控制参数自动优化标定系统的研究及验证[J]. 中国机械工程, 2022, 33(01): 118-125.
[6]	侯想, 刘熠新, 钟梦洁, 林赛, 刘杨, 罗荣煌, 罗学涛, 张飒, . 图形化蓝宝石衬底干法刻蚀工艺研究[J]. 中国机械工程, 2021, 32(24): 3001-3007.
[7]	王强, 陈继刚, 赵建华, 李雪, 胡占齐, . 航空自润滑关节轴承的内锥面滚铆工具设计[J]. 中国机械工程, 2021, 32(20): 2501-2507,2519.
[8]	杨艳玲, 禹静, 林希萌, 蔡晋辉. 三维螺纹测量机接触式测头的优化设计[J]. 中国机械工程, 2021, 32(15): 1812-1817.
[9]	汪建新, 吴耀文, 张广义, 潮阳, 张文武, . 碳纤维增强复合材料水导激光切割试验研究[J]. 中国机械工程, 2021, 32(13): 1608-1616.
[10]	龙江启1;林坚1;陈先兵2;王子宁2. 通风制动盘结构参数对制动抖动的敏感性[J]. 中国机械工程, 2020, 31(24): 2966-2971.
[11]	高建平;孙家辉;徐振海;郗建国. 基于行驶工况的插电式混合动力公交车控制参数自动化标定方法[J]. 中国机械工程, 2020, 31(06): 631-637.
[12]	陈尤旭1,2;王德山1;张伟1,2;金国庆1,2. 面向软体机器人的3D打印硅胶软材料实验研究[J]. 中国机械工程, 2020, 31(05): 603-609,629.
[13]	徐波1,2;干为民1,2;何亚峰1,2;李文静3;王祥志1,2. 阶梯孔数控电解镗孔加工的阴极设计及试验研究[J]. 中国机械工程, 2019, 30(12): 1498-1506.
[14]	郑子军;李攀星;蔡东海;文东辉. 液动压悬浮抛光流场的数值模拟及抛光工具盘结构优化[J]. 中国机械工程, 2019, 30(06): 638-643.
[15]	梁博健1;高殿荣2. 高压水除鳞喷嘴结构参数对喷嘴射流性能的影响[J]. 中国机械工程, 2018, 29(24): 2939-2946.

动力稳定作业参数对道床稳定性的影响

Effects of Dynamic Stabilization Operation Parameters on Ballast Stability

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics