聚碳酸酯超低温冷却车削表面形貌试验研究

doi:10.3969/j.issn.1004-132X.2024.02.002

中国机械工程 ›› 2024, Vol. 35 ›› Issue (02): 201-207.DOI: 10.3969/j.issn.1004-132X.2024.02.002

聚碳酸酯超低温冷却车削表面形貌试验研究

包锐;刘阔;张杰;韩灵生;李建明;左月帅;刘海波;王永青

大连理工大学高性能精密制造全国重点实验室,大连,116024

出版日期:2024-02-25 发布日期:2024-03-22
通讯作者: 刘海波（通信作者），男，1983年生，教授、博士研究生导师。研究方向为超低温冷却加工技术、测量-加工一体化制造方法与装备、在机/在位精密测量技术与系统。发表论文80余篇。E-mail：hbliu@dlut.edu.cn。
作者简介:包锐，男，1999 年生，硕士研究生。研究方向为超低温冷却加工技术。发表论文1篇。E-mail：2879779864@qq.com。
基金资助:
国家自然科学基金（U20B2033）；中央高校基本科研业务费专项资金（DUT22LAB505）

Experimental Study of Surface Morphology of Polycarbonate Ultra-low Temperature Cooling Turning

BAO Rui;LIU Kuo;ZHANG Jie;HAN Lingsheng;LI Jianming;ZUO Yueshuai;LIU Haibo;WANG Yongqing

National Key Laboratory of High Performance Precision Manufacturing,Dalian University of Technology,Dalian,Liaoning,116024

Online:2024-02-25 Published:2024-03-22

摘要/Abstract

摘要： 针对聚碳酸酯加工时存在的耐热性差、变形、溶胀等问题，分别在干切削、水冷和超低温冷却条件下进行了聚碳酸酯的车削试验，并分析了材料加工表面的形貌，从分子链弛豫时间、银纹产生和脆韧性转变的角度解释了加工表面形貌的差异。研究发现，聚碳酸酯干切削表面产生大量粗大银纹，水冷切削表面产生大量细密银纹，超低温冷却切削表面银纹较少，因此超低温冷却对提高聚碳酸酯的加工质量具有积极作用。

关键词: 聚碳酸酯, 超低温冷却切削, 银纹, 加工表面形貌

Abstract: Aiming at the problems of poor heat resistance, deformation, and swelling, a turning test of polycarbonate was carried out under dry cutting, water cooling, ultra-low temperature cooling, and the shape of the surface was analyzed. The morphological differences of machined surfaces were explained from the perspective of relaxation time of molecular chains, crazing generation, and brittle-toughness transition. It is found that, on polycarbonate surfaces, dry cutting produces a large number of strong crazing, water-cooled cutting produced a large number of fine crazing, while the ultra-low temperature cooling cutting produces less crazing. Therefore, ultra-low temperature cooling has a positive effect on improving the processing quality of polycarbonates.

Key words: polycarbonate, ultra-low temperature cooling cutting, crazing, machining surface morphology

中图分类号:

TH161

包锐, 刘阔, 张杰, 韩灵生, 李建明, 左月帅, 刘海波, 王永青. 聚碳酸酯超低温冷却车削表面形貌试验研究[J]. 中国机械工程, 2024, 35(02): 201-207.

BAO Rui, LIU Kuo, ZHANG Jie, HAN Lingsheng, LI Jianming, ZUO Yueshuai, LIU Haibo, WANG Yongqing. Experimental Study of Surface Morphology of Polycarbonate Ultra-low Temperature Cooling Turning[J]. China Mechanical Engineering, 2024, 35(02): 201-207.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2024.02.002

http://www.cmemo.org.cn/CN/Y2024/V35/I02/201

参考文献

［1］MAO X, YUK H, ZHAO X. Hydration and Swelling of Dry Polymers for Wet Adhesion［J］. Journal of the Mechanics and Physics of Solids, 2020, 137:103863.
［2］杨亮,孙明杰.聚碳酸酯振动切削温度仿真与试验研究［J］.工具技术,2021,55(11):49-52.
YANG Liang, SUN Mingjie. Simulation and Experimental Study on Vibration Cutting Temperature of Polycarbonate［J］. Tool Technology,2021,55(11):49-52.
［3］刘逢博,董如永.聚碳酸酯(PC)材料的精密加工工艺的研究和应用［J］.机电产品开发与创新,2009,22(6):188-190.
LIU Fengbo, DONG Ruyong. Research and Application of Precision Machining Technology of Polycarbonate (PC) Material［J］. Mechatronics Development and Innovation, 2009,22(6):188-190.
［4］袁凯. 超低温加工用液氮传输调控系统研制［D］.大连：大连理工大学,2017.
YUAN Kai. Development of Liquid Nitrogen Transfer Control System for Ultra-low Temperature Processing［D］. Dalian:Dalian University of Technology,2017.
［5］SHOKRANI A, DHOKIA V, MUOZ-ESCALONA P, et al. State-of-the-art Cryogenic Machining and Processing［J］. International Journal of Computer Integrated Manufacturing, 2013, 26(7):616-648.
［6］BALAJI V, RAVI S, CHANDRAN P N, et al. Review of the Cryogenic Machining in Turning and Milling Process［J］. Int. J. Res. Eng. Technol., 2015, 4(10):38-42.
［7］JAWAHIR I S, ATTIA H, BIERMANND, et al. Cryogenic Manufacturing Processes［J］. CIRP annals, 2016, 65(2):713-736.
［8］KHORAN M, AMIRABADI H, AZARHOUSHANG B. The Effects of Cryogenic Cooling on the Grinding Process of Polyether Ether Ketone (PEEK)［J］. Journal of Manufacturing Processes, 2020, 56:1075-1087.
［9］WANG Y, HAN L, LIU K, et al. Optimization of Jet Parameters for Minimizing Surface Roughness in Cryogenic Milling of Ti-6Al-4V［J］. Journal of Manufacturing Science and Engineering, 2021, 143(5):713-736.
［10］侯博,谢浔,崔超,等.石英纤维增强聚酰亚胺复合材料超低温铣削试验［J］.宇航材料工艺,2020,50(3):56-61.
HOU Bo, XIE Xun, CUI Chao, et al. Milling Experiment of Quartz Fiber Reinforced Polyimide Composites at Ultra-low Temperature［J］. Aerospace Materials Technology, 2020, 50(3):56-61.
［11］王永青,郭东明,郭立杰,等.超低温加工技术的研究现状及发展趋势［J］.上海航天,2020,37(3):11-21.
WANG Yongqing, GUO Dongming, GUO Lijie, et al. Research Status and Development Trend of Ultra-low Temperature Machining Technology［J］. Shanghai Aerospace, 2019,37(3):11-21.
［12］SHIH A J, LEWIS M A, STRENKOWSKI J S. End Milling of Elastomers—Fixture Design and Tool Effectiveness for Material Removal［J］. J. Manuf. Sci. Eng., 2004, 126(1):115-123.
［13］KAKINUMA Y, KIDANI S, AOYAMA T. Ultra-precision Cryogenic Machining of Viscoelastic Polymers［J］. CIRP Annals, 2012, 61(1):79-82.
［14］SONG K, GANG M G, JUN M B G, et al. Cryogenic Machining of PDMS Fluidic Channel Using Shrinkage Compensation and Surface Roughness Control［J］. International Journal of Precision Engineering and Manufacturing, 2017, 18:1711-1717.
［15］DHOKIA V G, NEWMAN S T, CRABTREE P, et al. A Methodology for the Determination of Foamed Polymer Contraction Rates as a Result of Cryogenic CNC Machining［J］. Robotics and Computer-Integrated Manufacturing, 2010, 26(6):665-670.
［16］YILDIZ Y, NALBANT M. A Review of Cryogenic Cooling in Machining Processes［J］. International Journal of Machine Tools and Manufacture, 2008, 48(9):947-964.
［17］华幼卿, 金日光. 高分子物理［M］. 4版.北京:化学工业出版社, 2013.
HUA Youqing, JIN Liangliang. Polymer Physics［M］. 4th ed. Beijing:Chemical Industry Press, 2013.
［18］励杭泉, 张晨. 聚合物物理学［M］. 北京:化学工业出版社, 2007.
LI Hangquan, ZHANG Chen. Polymer Physics［M］. Beijing:Chemical Industry Press, 2007.
［19］ARGON A S, HANNOOSH J G. Initiation of Crazes in Polystyrene［J］. Philosophical Magazine, 1977, 36(5):1195-1216.
［20］WANG Y, WANG S, LIU K, et al. Effect of Indirect Cryogenic Cooling on the Machining Accuracy and Tool Vibration in the Turning of Polysulfone［J］. Journal of Manufacturing Science and Engineering:Transactions of the ASME, 2022(6):144.
［21］WANG Y, LI J, LIU K, et al. Experiment and Numerical Study of Chip Formation Mechanism during Cryogenic Machining of Ti-6Al-4V Alloy［J］. Journal of Manufacturing Processes, 2022, 84:1246-1257.
［22］何平笙. 高聚物的力学性能［M］. 2版. 合肥:中国科学技术大学出版社, 2008.
HE Pingsheng. Mechanical Properties of Polymers［M］. 2nd ed. Hefei:University of Science and Technology of China Press, 2008.

[1]	杜煦, 常泽鑫, 郑军强, 任鹏飞. 一种考虑关节跃度约束的实时刀具路径光顺算法[J]. 中国机械工程, 2024, 35(02): 280-286.
[2]	梁小冰, 卢耀安, 王成勇, . 双转台五轴机床旋转轴位置无关几何误差的辨识[J]. 中国机械工程, 2023, 34(21): 2585-2591.
[3]	王明, 董海, 王柏何, 王峥, 王加威. 2.5D Cf/SiC刹车材料浮动磨削工艺试验研究[J]. 中国机械工程, 2023, 34(20): 2434-2441.
[4]	韩锐, 李秀红, 王嘉明, 李文辉, 程思源, 杨胜强, . 水平强制振动光整加工对TC4钛合金表面完整性参数的影响[J]. 中国机械工程, 2023, 34(17): 2037-2047.
[5]	朱思佩, 付国强, 郑悦, 李正堂, 杨吉祥. 五轴曲面铣削的通用表面纹理形貌建模方法[J]. 中国机械工程, 2023, 34(16): 1946-1957.
[6]	迟玉伦, 武子轩. 基于磨削热变形分析的切入式外圆磨削去除率的修正模型与实验研究[J]. 中国机械工程, 2023, 34(15): 1778-1788.
[7]	鲁艳军, 关伟锋, 孙佳劲, 莫睿, 伍晓宇. 基于放电修锐的粗金刚石砂轮干式镜面磨削技术[J]. 中国机械工程, 2023, 34(09): 1052-1060.
[8]	付高财, 盛步云, 万润, 殷希彦, 盛甘霖. 一种复杂曲面无基准轮廓度的ER-BFGS评定方法[J]. 中国机械工程, 2023, 34(08): 923-930.
[9]	张硕, 邹平, 方锐, 周亮. 微织构车刀椭圆超声辅助切削加工性能研究[J]. 中国机械工程, 2023, 34(03): 287-291，299.
[10]	何坤, 何晓虎, 杜彦斌. 圆柱齿轮滚切倒棱刀具设计[J]. 中国机械工程, 2022, 33(22): 2704-2710.
[11]	潘博, 康仁科, 贺增旭, 李凯隆, 张云飞, 黄文, 郭江. 弱刚性构件磁流变抛光变形机理与抑制技术研究[J]. 中国机械工程, 2022, 33(18): 2190-2196.
[12]	邓乾发, 程军, 吕冰海, 袁巨龙, 王旭, 岑凯迪, . 介电泳效应平面抛光的电极同层布置方式数值仿真与实验[J]. 中国机械工程, 2022, 33(15): 1772-1779，1793.
[13]	卢成伟, 钱博增, 王慧敏, 项四通. 工件分特征下的五轴数控机床关键几何误差分析与补偿方法[J]. 中国机械工程, 2022, 33(14): 1646-1653.
[14]	易茜, 李聪波, 潘建, 张友. 薄板类零件加工精度可靠性分析及工艺参数优化[J]. 中国机械工程, 2022, 33(11): 1269-1277.
[15]	郭曦鹏, 徐闻, 王定文, 李蓉, 尹韶辉. 纳米精度在位测量系统测头误差校正方法[J]. 中国机械工程, 2022, 33(09): 1084-1089.

聚碳酸酯超低温冷却车削表面形貌试验研究

Experimental Study of Surface Morphology of Polycarbonate Ultra-low Temperature Cooling Turning

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics