Output Displacement Analysis of a Parallel Leaf Spring

China Mechanical Engineering ›› 2010, Vol. 21 ›› Issue (04): 391-393,436.

Previous Articles Next Articles

Output Displacement Analysis of a Parallel Leaf Spring

Yang Xuefeng1;Li Wei1;Wang Yuqiao1;Ye Guo1;Su Xiuping2

1.China University of Mining and Technology,Xuzhou,Jiangsu,221116

2.Xuzhou Normal University,Xuzhou,Jiangsu,221116

Online:2010-02-25 Published:2010-03-10
Supported by:
Specialized Research Fund for the Doctoral Program of Higher Education of China（No. 20090095110012）

平行片簧机构输出位移分析

杨雪锋1;李威1;王禹桥1;叶果1;苏秀平2

1.中国矿业大学,徐州,221116

2.徐州师范大学,徐州,221116

基金资助:
高等学校博士学科点专项科研基金资助项目(20090095110012)；江苏省研究生培养创新工程资助项目(CX07B_071z)
Specialized Research Fund for the Doctoral Program of Higher Education of China（No. 20090095110012）

Abstract

Abstract:

According to the symmetrical structure,the output displacement characteristics of a parallel leaf spring at large deformation were analyzed by using the Bernoulli-Euler formula and the homotopy analysis method.And a half beam model was established based on the force analysis and deformation analysis of the leaf spring.The guiding displacement and coupled displacement formulas were derived and verified by finite element analysis.Results show that the analytic solution has higher accuracy even when the guiding displacement and the coupled displacement reach to the 34% and 8% of the length of the leaf spring separately.

Key words:

parallel leaf spring, half beam model, guiding displacement, coupled displacement

摘要：

为了分析平行片簧机构在大变形状态下的位移输出特性，根据其结构的对称性，利用Bernoulli-Euler方程和同伦分析方法，在对单个片簧进行受力分析和变形分析的基础上建立了片簧的半段梁模型，得出了一种计算平行片簧机构输出导向位移和耦合位移解析解的方法，并采用有限元方法进行了分析验证。结果表明，在导向位移为片簧长度的34%时，耦合位移达到片簧长度的8%，此时该解析解仍具有较高的精度。

关键词:

平行片簧, 半段梁模型, 导向位移, 耦合位移

CLC Number:

TH132

YANG Xue-Feng, LI Wei, WANG Yu-Qiao, XIE Guan, SU Xiu-Beng.

Output Displacement Analysis of a Parallel Leaf Spring

[J]. China Mechanical Engineering, 2010, 21(04): 391-393,436.

杨雪锋, 李威, 王禹桥, 叶果, 苏秀平.

平行片簧机构输出位移分析

[J]. 中国机械工程, 2010, 21(04): 391-393,436.

References

[1]Alexandre E G, Spencer P M, Larry L H, et al.Compliant Joint Design Principles for High Compressive Load Situations[J]. Journal of Mechanical Design,Transactions of the ASME, 2005,127 (4) : 774-781.
[2]王勇[1],刘志刚[1],薄锋[1],朱健强[1].五自由度纳米级定位工作台的设计研究[J].中国机械工程,2005,16(15):1317-1321.
[3]李庆祥等编著.现代精密仪器设计[M],2004:549.
[4]牟新明[1],王建华[1],杨密[1].平行簧片机构力学分析与计算[J].纳米技术与精密工程,2005,3(4):278-282.
[5]Ryu J W,Lee S Q,Gweon D G,et al. Inverse Kinematics Modeling of a Coupled Flexure Hinge Mechanism[J]. Mechatronics, 1999,9(6) :657-674.
[6]Her I,Chang J C. A Linear Scheme for the Displacement Analysis of Micropositioning Stages with Flexure Hinges[J]. Journal of Mechanical Design, 1994,116(9) :770-776.
[7]王华 [1],张宪民 [2],欧阳高飞 [2].平面三自由度微动工作台的输入耦合分析[J].中国机械工程,2005,16(5):377-380.
[8]沈剑英 [1],杨世锡 [1],周庆华 [2],严拱标 [1],曹坚 [2].单平行四杆柔性铰链机构的输出位移和耦合误差分析[J].机床与液压,2004(3):27-28.
[9]Howell L L. Complaint Meehanisms[M]. New York:John Wiley & Sons,Inc. ,2001.
[10]王华伟[1],余跃庆[1],苏丽颖[1],王雯静[1].柔顺机构动力学建模新方法[J].机械工程学报,2008,44(10):96-103.
[11]赵宏伟[1],吴博达[1],曹殿波[2],华顺明[1],程光明[1],杨志刚[1],曲兴田[1].直角柔性铰链的力学特性[J].纳米技术与精密工程,2007,5(2):143-147.
[12]Hyung K J. Hyun K S, Keun K Y. Development and Optimization of 3- D Bridge--Type Hinge Mechanisms[J]. Sensors and Actuators, 2004,116 (3) ,530-538.
[13]Wang Ji, Chen Jiankang, Liao Shijun. An Explicit Solution of the Large Deformation of a Cantilever Beam under Point Load at the Free Tip[J]. Journal of Computational and Applied Mathematics, 212(2): 320-330.
[14]Young W C,Budynas R G. Roark's Formulas for Stress and Strain[M]. 7 ed. New York: McGrawHill,2002.

Output Displacement Analysis of a Parallel Leaf Spring

平行片簧机构输出位移分析

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 10

Recommended Articles

Metrics

[1]	MAO Shi-Gang, FENG Xian-Yang, LI Lei. Load Tooth Contact Analysis on Globoidal Cam Continuous Transmission Mechanism with Balls [J]. China Mechanical Engineering, 2012, 23(4): 379-382.
[2]	GU Ju-Min, GAO Bei. A Novel Noncircular Planetary Differential for Off-road Vehicles [J]. China Mechanical Engineering, 2012, 23(3): 346-348.
[3]	LIN Yu-Bei-1, HU Li-Zhong-1, LIANG Yong-Li-1, 2. Force and Deformation Analyses for Flexspline of an Electromechanical Integrated Electromagnetic Harmonic Friction Drive [J]. China Mechanical Engineering, 2011, 22(10): 1169-1172.
[4]	JI De-Sheng, HUANG Xue-Gong, WANG Yong. Study on Modified Involute Profile Roller Chain Sprocket and Its Dynamic Features [J]. China Mechanical Engineering, 2011, 22(9): 1118-1122.
[5]	HAO Xiu-Gong, HU Li-Zhong, ZHENG Da-Zhou. Strongly Nonlinear Vibration Study of Electromechanical Integrating Toroidal Drive System [J]. China Mechanical Engineering, 2010, 21(19): 2278-2284.
[6]	XIAO Zheng-Meng, QIN Da-Tong, WANG Jian-Hong, WU Wen-Hui, CHEN Li-Feng. Study on Torsional Dynamics of 3-stage Planetary Gears of Main Reducer Used in Driving Cutterhead of Shield Tunnelling Machine [J]. China Mechanical Engineering, 2010, 21(18): 2176-2182.
[7]	WANG Guo-Biao, LAI Yi-Nan, FAN Da-Feng, YANG Hua-Yong, WANG Shi-Long. Summary of New Type Precision Transmission Design and Manufacture [J]. J4, 201016, 21(16): 1891-1897.
[8]	WANG Guo-Biao, LAI Yi-Nan, FAN Da-Feng, YANG Hua-Yong, WANG Shi-Long. Summary of New Type Precision Transmission Design and Manufacture [J]. China Mechanical Engineering, 2010, 21(16): 1891-1897.
[9]	CHANG Le-Gao, LIU Geng, TUN Li-Yan, XU Yi-Pei. A Method for Calculating Tooth Bending Stress of a Herringbone Planetary Train System in Engagement Process [J]. China Mechanical Engineering, 2010, 21(11): 1305-1309.
[10]	CAO Kang, TANG Jin-Yuan, LI Guo-Shun, LIU Yan-Ping. Least Parametrical Modification Method of Spiral Bevel Gear Tooth Surface Errors [J]. China Mechanical Engineering, 2010, 21(04): 469-476.