Simulation Analysis of Temperature Fields and Parameter Optimization of Stationary Shoulder Friction Stir Welding

doi:10.3969/j.issn.1004-132X.2022.17.013

Abstract

Abstract: In order to solve the problems of welding failures caused by the traditional stirring head which easily fell into the welded plates under the conditions of non rigid support， the stationary shoulder welding structure was designed and developed. By establishing the finite element simulation model and using the thermal infrared imager to monitor the welding surface temperature in real time， the changes of temperature fields during stationary shoulder friction stir welding under different processing parameters were analyzed. The stationary shoulder friction stir welding designed and developed were used for field tests， and the tensile tests were carried out to compare the welds without defects on the welded surfaces with the base metal， the mechanical strength of the welds was detected， and the microstructure of the fracture was analyzed. The results show that in the welding processes of stirring head with stationary shoulder， the heat generation mainly comes from the friction heat generated by the shoulder and the end of the stirring needle， and the side friction heat generated by the stirring needle and the friction heat generated by the stationary shoulder account for a small proportion. The spindle pressure and spindle speed have great influences on heat production， and the C-axis speed has little influences on heat production. Under the processing parameters of spindle pressure of 2940～3430 N， spindle speed of 1000 r/min and C-axis speed of 0.05 r/min， the surface of the welded seams is smooth without flash， there are no groove and tunnel defects inside， the tensile property of the welds reaches about 71.5% of the base metal. There is delamination in the weld fracture. The upper layer near the welding surface shows brittle fracture characteristics， and the lower layer shows ductile fracture characteristics. Compared with the base metals， the elongation and tensile strength of the weld specimens are reduced.

Key words: stationary shoulder, friction stir welding, processing parameter, temperature field, experimental research

摘要： 为了解决非刚性支撑条件下传统搅拌头易陷入被焊接板材而导致焊接失败的问题，设计研发了静轴肩焊接结构。通过建立有限元仿真计算模型，并使用热红外成像仪对焊接表面温度进行实时监测，分析不同工艺参数下静轴肩摩擦搅拌焊焊接过程中的温度场变化情况。使用设计研发的静轴肩摩擦搅拌焊进行现场试验并对完成焊接表面无缺陷的焊缝与母材进行拉伸试验对比，检测其焊缝机械强度，并对断口进行微观组织分析。结果表明：在使用静轴肩搅拌头焊接过程中，产热量主要来源于搅拌针轴肩的摩擦生热和搅拌针端部的摩擦生热，搅拌针的侧面摩擦生热和静轴肩的摩擦生热占比较小；对产热量影响较大的是主轴压力和主轴转速，C轴转速对产热量影响不大；在主轴压力为2940～3430 N，主轴转速为1000 r/min，C轴转速为0.05 r/min的工艺参数下，完成焊接的焊缝表面光滑无飞边，内部无沟槽隧道缺陷，焊缝抗拉性能达到母材的71.5%左右；焊缝断口存在分层现象，靠近焊接表面的上层呈脆性断裂特性，下层呈延性断裂特性，与母材相比，焊缝试样的延伸率和抗拉强度均有所降低。

关键词: 静轴肩, 摩擦搅拌焊, 工艺参数, 温度场, 试验研究

CLC Number:

TG453

ZHANG Jun, WANG Wen, WANG Jian, JIN Taotao, TIAN Zhipeng. Simulation Analysis of Temperature Fields and Parameter Optimization of Stationary Shoulder Friction Stir Welding[J]. China Mechanical Engineering, 2022, 33(17): 2115-2124.

张军, 王稳, 王健, 金涛涛, 田志鹏. 静轴肩摩擦搅拌焊温度场仿真分析与参数优化[J]. 中国机械工程, 2022, 33(17): 2115-2124.

References

［1］KIM Y P， KIM C H， KIM Y G， et al. Trends of Technology Development of Friction Stir Welding Machine［J］. Journal of Welding and Joining， 2016， 34（3）：1-5.
［2］相倩，吕念春，薛鹏，等. 铝-钢异种金属搅拌摩擦焊研究现状及展望［J］. 机械工程学报， 2017， 53（20）：28-37.
XIANG Qian， LYU Nianchun， XUE Peng， et al. Research Status and Prospect on Friction Stir Welded Dissimilar Al-steel Joints［J］. Journal of Mechanical Engineering， 2017， 53（20）：28-37.
［3］张文毓. 铝合金焊接技术研究进展［J］. 轻金属， 2010， 47（4）：53-56.
ZHANG Wenyu. Aluminium Alloy Welding Engineering Research Progress［J］. Light Metals， 2010， 47（4）：53-56.
［4］徐波，但楚臣，何兆坤，等. 镁/铝合金回填式搅拌摩擦点焊的组织与性能［J］. 焊接学报， 2019， 40（11）：106-110.
XU Bo， DAN Chuchen， HE Zhaokun， et al. Microstructure and Mechanical Properties of Refill Friction Stirspot Welded Dissimilar Mg/Al Alloys［J］. Transactions of The China Welding Institution， 2019， 40（11）：106-110.
［5］杨亚楠，刘振邦，仪家良. 搅拌摩擦焊技术应用现状与发展趋势［J］. 工程技术研究， 2017， 40（2）：57-58.
YANG Yalan， LIU Zhengbang， YI Jialiang. Application Status and Development Trend of FSW Technology［J］. Engineering Technology and Application， 2017， 40（2）：57-58.
［6］褚强，郝思洁， Devang Sejani，等. 静止轴肩搅拌摩擦焊接研究进展及展望［J］. 电焊机， 2020， 50（9）：44-52.
CHU Qiang， HAO Sijie， Devang Sejani， et al. Development and Prospect of Stationary Shoulder Friction Stir Welding［J］. Electric Welding Machine， 2020， 50（9）：44-52.
［7］方远方，张华. 铝合金型材的静轴肩倾斜搅拌摩擦焊接头性能［J］. 中国机械工程， 2021， 32（7）：815-820.
FANG Yuanfang， ZHANG Hua. Welding Joint Performance of Inclined Stationary Shoulder Friction Stir Welding for Aluminum Alloy Sections［J］. China Mechanical Engineering， 2021， 32（7）：815-820.
［8］RUSSELL M J， BLIGNAULT C， HORREX N L， et al. Recent Developments in the Friction Stir Welding of Titanium Alloys［J］. Welding in the World， 2008， 52（9/10）：12-15.
［9］WU Hao， CHEN Yingchun， STRONG D， et al. Systematic Evaluation of the Advantages of Static Shoulder FSW for Joining Aluminium［J］. Materials Science Forum， 2014， 794/796（1）：407-412.
［10］AVETTAND-FENOEL M N， TAILLARD R. Effect of a Pre or Postweld Heat Treatment on Microstructure and Mechanical Properties of an AA2050 Weld Obtained by SSFSW［J］. Materials and Design， 2016， 89（37）：348-361.
［11］姬书得，孟祥晨，黄永宪，等. 搅拌头旋转频率对静止轴肩搅拌摩擦焊接头力学性能的影响规律［J］. 焊接学报， 2015， 36（1）：51-54.
JI Shude， MENG Xiangchen， HUANG Yongxian， et al. Effect of Rotational Velocity of Tool on Mechanical Properties of Stationary Shoulder Friction Stir Welding［J］. Transactions of the China Welding Institution， 2015， 36（1）：51-54.
［12］LI J Q， LIU H J. Effects of Tool Rotation Speed on Microstructures and Mechanical Properties of AA2219-T6 Welded by the External Non-rotational Shoulder Assisted Friction Stir Welding［J］. Materials&Design， 2013， 43（12）：299-306.
［13］BUFFA G， FRATINI L， IMPERO F， et al. Surface and Mechanical Characterization of Stationary Shoulder Friction Stir Welded Lap Joints：Experimental and Numerical Approach［J］. International Journal of Material Forming， 2020， 13（1）：725-736.
［14］王瑾，李送斌，张妍，等. 焊接工艺参数对6061-T6铝合金静止轴肩搅拌摩擦焊组织及力学性能的影响［J］. 焊接， 2019， 1（11）：33-38.
WANG Jin， LI Songbin， ZHANG Yan， et al. Effect of Welding Parameters on Microstructure and Mechanical Properties of 6061-T6 Joints by Stationary Shoulder Friction Stir Welding［J］. Welding & Joining， 2019， 1（11）：33-38.
［15］赵俊，柯黎明，黄斌，等. 工艺参数对铝合金静轴肩搅拌摩擦焊焊缝成形的影响［J］. 热加工工艺， 2019， 48（13）：22-25.
ZHAO Jun， KE Liming， HUANG Bin， et al. Influnence of Process Parameter on Weld Formation of Stationary Shoulder Friction Stir Welding of Aluminum Alloy［J］. Hot Working Technology， 2019， 48（13）：22-25.
［16］申浩，杨新岐，李冬晓，等. 6061-T6铝合金的静止轴肩搅拌摩擦焊工艺及组织性能［J］. 焊接学报， 2016， 37（5）：119-123.
SHEN Hao， YANG Xinqi， LI Dongxiao， et al. Microstructures and Mechanical Properties of 6061-T6 Aluminum Alloy Welded by Stationary Shoulder Friction Stir Welding Process［J］. Transactions of the China Welding Institution， 2016， 37（5）：119-123.
［17］刘志伟. 基于COMSOL的搅拌摩擦焊热场影响因素数值计算［D］. 成都：西华大学， 2016.
LIU Zhiwei. Numerical Calculation of the Influence Factors on the Thermal Field of Friction Stir Welding Based on COMSOL［D］. Chengdu：Xihua University， 2016.
［18］周文静，杜柏松，卢小明. 铝合金搅拌摩擦焊温度场数值模拟及参数影响分析［J］. 热加工工艺， 2021， 50（7）：156-160.
ZHOU Wenjing， DU Baisong， LU Xiaoming. Numerical Simulation of Temperature Field and Parameter Influence Analysis of Friction Stir Welding of Aluminum Alloy［J］. Hot Working Technology， 2021， 50（7）：156-160.
［19］柴鹏，左莹莹，陈克鹏，等. 回填式搅拌摩擦点焊过程温度场的数值模拟［J］. 航空制造技术， 2020， 63（11）：34-40.
CHAI Peng， ZUO Yingying， CHEN Kepeng， et al. Numerical Simulation of Temperature Fieldduring Refill Friction Stir Spot Welding［J］. Aeronautical Manufacturing Technology， 2020， 63（11）：34-40.
［20］莫淑娴，朱浩，马泽铭，等. 铝/钢异种金属搅拌摩擦焊接头数值模拟［J］. 兵器材料科学与工程， 2020， 43（3）：13-18.
MO Shuxian， ZHU Hao， MA Zeming. Numerical Simulation of Friction Stir Welding Joint of Aluminum/Steel Dissimilar Metal［J］. Ordnance Material Science and Engineering， 2020， 43（3）：13-18.
［21］苗臣怀，曹丽杰，殷凯，等. 铝合金-钢搅拌摩擦焊温度场数值研究［J］. 轻工机械， 2019， 37（6）：82-87.
MIAO Chenhuai， CAO Lijie， YIN Kai， et al. Numerical Simulation of Temperature Field in Aluminum Alloy-steel Friction Stir Welding［J］. Light Industry Machinery， 2019， 37（6）：82-87.
［22］鱼海东，崔国华，张振山，等. 搅拌摩擦焊双轴肩搅拌针产热模型与温度场研究［J］. 轻工机械， 2019， 37（4）：35-41.
YU Haidong， CUI Guohua， ZHANG Zhenshan， et al. Mathematical Thermal Model and Thermal Filed for Bobbin Tool Friction Stir Welding［J］. Light Industry Machinery， 2019， 37（4）：35-41.
［23］陈彦君. 基于ABAQUS的搅拌摩擦焊仿真模拟分析［D］. 大连：大连交通大学， 2019.
CHEN Yanjun. Simulation Analysis of Friction Stir Welding Based on ABAQUS Software［D］. Dalian：Dalian Jiaotong University， 2019.
［24］卢翔，邵良臣，李志勇，等. DP590钢/AA6061-T6铝合金异种金属对接搅拌摩擦焊温度场的数值模拟［J］. 热加工工艺， 2021， 50（1）：151-155.
LU Xiang， SHAO Liangchen， LI Zhiyong， et al. Numerical Simulation of Temperature Field of Friction Stir Butt Weldingof DP590 Steel/AA6061-T6 Aluminum Alloy［J］. Hot Working Technology， 2021， 50（1）：151-155.
［25］SUN G， WANG C， WEI X， et al. Study on Small Fatigue Crack Initiation and Growth for Friction Stir Welded Joints［J］. Materials Science and Engineering：A， 2019， 739：71-85.

[1]	TUN Fu-Chao, TUN Bai-Hu, ZHANG Xiu-Hua. Numerical Simulation of Heat Transfer Performance of Paraffin Thermal-Sensitive Valve  [J]. J4, 201016, 21(16): 1921-1926.
[2]	ZHANG Jinyang, XU Weichun, WANG Xiaohan, JIANG Xiaohui, GAO Shan. Study on Influences of Milling Process Optimization on Residual Stress Distribution for Machining Nickel-based Superalloys [J]. China Mechanical Engineering, 2024, 35(04): 624-635.
[3]	ZHA Xuming, YUAN Zhi, QIN Hao, XI Linqing, ZHANG Tao, JIANG Feng. Ultrasonic Impact Strengthening of Titanium Alloys：State-of-the-art and Prospectives [J]. China Mechanical Engineering, 2023, 34(19): 2269-2287.
[4]	DUAN Lingyun, HUANG Chuanzhen, LIU Dun, YAO Peng, LIU Hanlian. An Experimental Investigation of Laser Assisted Waterjet Microgrooving of GaAs Wafers [J]. China Mechanical Engineering, 2023, 34(10): 1172-1183.
[5]	LI Guolong, ZHU Guohua, JIANG Lin, TAO Yijie, JIA Yachao. Optimization of Multi-objective Grinding Process Parameters to Suppress Chatter Marks [J]. China Mechanical Engineering, 2023, 34(09): 1086-1092.
[6]	CHEN Geng, XIANG Hua, YE HanXIAO Fei. Research on Robot Abrasive Belt Grinding Parameters Considering the Change of Normal Contact Force [J]. China Mechanical Engineering, 2023, 34(07): 803-811，820.
[7]	HAN Jiang, LI Zhenfu, TIAN Xiaoqing, FEI Ningzhong, XIA Lian, . Research on Prediction and Control Method of Workpiece Tooth Flank Texture during Internal Gear Power Honing [J]. China Mechanical Engineering, 2023, 34(01): 10-16.
[8]	TAO Shuangquan, HAO Xiaozhong, YANG Zijian, LIU Shuting. Hybrid of Self-resistance Electric Heating and In-situ Membrane Heating of CF/PEEK Composites Consolidation [J]. China Mechanical Engineering, 2022, 33(22): 2748-2754.
[9]	LIU Xu, SUN Yuli, ZHANG Guiguan, QIAN BingkunG, AO Hang, ZUO Dunwen. Simulation and Experimental Research about Temperature Fields of PDMS Cooled by Liquid Nitrogen Jet Impingement [J]. China Mechanical Engineering, 2022, 33(18): 2161-2171.
[10]	LIU Liye, CHEN Yongliang, TANG Weili, WEI Yunpeng, SUO Shucan. Research on Open Control Systems and Tangent Tracking of Friction Stir Welding Machines [J]. China Mechanical Engineering, 2022, 33(16): 1948-1956.
[11]	SHU Zihao, PANG Qilong, KUANG Liangjie. Effects of Frequency Features Generated in Machined Surface on Subsurface Temperature Field of KH2PO4 Crystals [J]. China Mechanical Engineering, 2022, 33(16): 1983-1991.
[12]	YI Qian, LI Congbo, PAN Jian, ZHANG You. Reliability Analysis of Machining Accuracy and Processing Parameter Optimization for Thin-plate Parts [J]. China Mechanical Engineering, 2022, 33(11): 1269-1277.
[13]	QIAN Yingping, XUE Hang, MEI Jianliang. Research on On-line Quality Monitoring Method for Injection Molding Products of Crystalline Plastic [J]. China Mechanical Engineering, 2022, 33(09): 1073-1076,1083.
[14]	YU Guoda, LIU Huaiju, LU Zehua, WEI Peitang. Simulation and Experimental Study of Steady-state Temperature Field of Plastic Gears under Grease Lubrication Conditions#br# [J]. China Mechanical Engineering, 2022, 33(08): 890-898，907.
[15]	NI Hengxin, YAN Chunping, SUN Han, XU Teng, HUANG Yigong, ZHOU Chao. Energy Consumption Distribution Characteristics and Prediction Model of High-speed Dry Gear Hobbing Machine [J]. China Mechanical Engineering, 2022, 33(07): 842-851.