Study on Mechanics Properties and Energy Absorption of Gradient Porous Scaffolds Fabricated by SLM

doi:10.3969/j.issn.1004-132X.2022.19.011

Abstract

Abstract: Gradient Ti6Al4V porous scaffolds were designed based on triply periodic minimal surfaces（TPMS） and were fabricated by SLM technology. The effects of edge porosity Pout， center porosity Pin and average porosity P- on mechanics properties and energy absorption were analyzed. The results show that elastic modulus， compressive strength and total absorbed energy per unit volume WV of gradient porous scaffolds with the same P- all decrease with the increase of Pout and increase with the increase of Pin. The elastic modulus， compressive strength and WV of gradient porous scaffolds with the different P- all decrease with the increase of P-. P- has greater influence on elastic modulus， compressive strength and WV than Pin and Pout. The printed gradient porous scaffolds meet the requirements of elastic modulus and compressive strength of femur and tibia. The mechanics property model established may provide a reference for the applications of porous scaffolds in orthopedics.

Key words: , selective laser , melting（SLM）, gradient porous scaffold, mechanics property, energy absorption

摘要： 基于三周期极小曲面设计梯度Ti6Al4V多孔支架，并采用选区激光熔化打印成形，分析边缘孔隙率Pout、中心孔隙率Pin和平均孔隙率P-对力学性能和能量吸收的影响。研究结果表明：相同P-的梯度多孔支架弹性模量、抗压强度和单位体积的总吸收能量WV都随着Pout的增大而减小，随着Pin的增大而增大；不同P-的梯度多孔支架弹性模量、抗压强度和WV随着P-的增大而减小；P-对其弹性模量、抗压强度和WV的影响大于Pin、Pout的影响。打印成形的梯度多孔支架能够满足股骨和胫骨的弹性模量、抗压强度要求，建立的力学性能模型可为面向骨科医学多孔支架的应用提供参考。

关键词: 选区激光熔化, 梯度多孔支架, 力学性能, 能量吸收

CLC Number:

TN249
TB31

ZENG Shoujin, LI Chuansheng, LIU Guang, XU Mingsan, LI Dichen. Study on Mechanics Properties and Energy Absorption of Gradient Porous Scaffolds Fabricated by SLM[J]. China Mechanical Engineering, 2022, 33(19): 2364-2371.

曾寿金, , 李传生, 刘广, 许明三, 李涤尘. 选区激光熔化梯度多孔支架力学性能和能量吸收研究[J]. 中国机械工程, 2022, 33(19): 2364-2371.

References

［1］LI S J， ZHAO S， HOU W T， et al. Functionally Graded Ti-6Al-4V Meshes with High Strength and Energy Absorption［J］. Advanced Engineering Materials， 2016， 18（1）：34-38.
［2］KUMAR A， NUNE K C， MURR L E， et al. Biocompatibility and Mechanical Behaviour of Three-Dimensional Scaffolds for Biomedical Devices：Process-structure-property Paradigm［J］. International Materials Reviews， 2016， 61（1）：20-45.
［3］YIN H F， WEN G L， WU X， et al. Crashworthiness Design of Functionally Graded Foam-filled Multi-cell Thin-walled Structures［J］. Thin-walled Structures， 2014， 85：142-155.
［4］高芮宁，熊胤泽，张航，等. SLM制备径向梯度多孔钛/钽的力学性能及生物相容性［J］. 稀有金属材料与工程， 2021， 50（1）：249-254.
GAO Ruining， XIONG Yinze， ZHANG Hang， et al. Mechanical Properties and Biocompatibilities of Radially Graded Porous Titanium/Tantalum Fabricated by Selective Laser Melting［J］. Rare Metal Materials and Engineering， 2021， 50（1）：249-254.
［5］史振伟，王敏杰，戚文军，等. 激光选区熔化3 D打印AlSi10Mg合金的铺粉厚度研究［J］. 中国机械工程， 2022， 33（8）：959-964.
SHI Zhengwei， WANG Mingjie， QI Wenjun， et al. Study of Layer Thickness on Laser Selective Melting of 3D Printed AlSi10Mg［J］. China Mechanical Engineering， 2022， 33（8）：959-964.
［6］HU X Y， MIN X， RICKY C， et al. Piezoelectric Properties of Triply Periodic Minimum Surface Structures［J］. Composites Science and Technology， 2020， 200：108417.
［7］MA Z， ZHANG D Z， LIU F， et al. Lattice Structures of Cu-Cr-Zr Copper Alloy by Selective Laser Melting：Microstructures， Mechanical Properties and Energy Absorption［J］. Materials & Design， 2020， 187：108406.
［8］YANEZ A， HERRERA A， MARTEL O， et al. Compressive Behaviour of Gyroid Lattice Structures for Human Cancellous Bone Implant Applications［J］. Materials Science & Engineering：C， 2016， 68：445-448.
［9］LEI Y， MERTENS R， FERRUCCI M， et al. Continuous Graded Gyroid Cellular Structures Fabricated by Selective Laser Melting：Design， Manufacturing and Mechanical Properties［J］. Materials & design， 2019， 162：394-404.
［10］XIONG Y Z， GAO R N， ZHANG H， et al. Rationally Designed Functionally Graded Porous Ti6Al4V Scaffolds with High Strength and Toughness Built via Selective Laser Melting for Load-bearing Orthopedic Applications［J］. Journal of the Mechanical Behavior of Biomedical Materials， 2020， 104：103673.
［11］YANG L， HAN C J， WU H Z， et al. Insights Into Unit Cell Size Effect on Mechanical Responses and Energy Absorption Capability of Titanium Graded Porous Structures Manufactured by Laser Powder Bed Fusion［J］. Journal of the Mechanical Behavior of Biomedical Materials， 2020， 109：103843.
［12］高芮宁，李祥. 径向梯度多孔支架设计与力学性能分析［J］. 机械工程学报， 2021， 57（3）：220-226.
GAO Ruining， LI Xiang. Design and Mechanical Properties Analysis of Radial Gradient Porous Scaffolds［J］. Journal of Mechanical Engineering， 2021， 57（3）：220-226.
［13］石志良，卢小龙，黄琛，等. 钛合金植入物梯度孔结构设计及其力学性能［J］. 稀有金属材料与工程， 2019， 48（6）：1829-1834.
SHI Zhiliang， LU Xiaolong， HUANG Chen， et al. Structural Design and Mechanical Properties of Gradient Holes in Titanium Alloy Implants［J］. Rare Metal Materials and Engineering， 2019， 48（6）：1829-1834.
［14］LIMMAHAKHUN S， OLOYEDE A， SITTHISERIPRATIP K， et al. Stiffness and Strength Tailoring of Cobalt Chromium Graded Cellular Structures for Stress-Shielding Reduction［J］. Materials & Design， 2017， 114：633-641.
［15］BAEL S V， KERCKHOFS G， MOESEN M， et al. Micro-CT-based Improvement of Geometrical and Mechanical Controllability of Selective Laser Melted Ti6Al4V Porous Structures［J］. Materials Science & Engineering A， 2011， 528（24）：7423-7431.
［16］李祥，高芮宁，熊胤泽，等. 基于TPMS结构的多孔钛制备与表征［J］. 稀有金属材料与工程， 2020， 49（1）：325-330.
LI Xiang， GAO Ruining， XIONG Yinze， et al. Fabrication and Characterization of Porous Titanium Based on TPMS Structure［J］. Rare Metal Materials and Engineering， 2020， 49（1）：325-330.
［17］HAN C J， LI Y， WANG Q， et al. Continuous Functionally Graded Porous Titanium Scaffolds Manufactured by Selective Laser Melting for Bone Implants［J］. Journal of the Mechanical Behavior of Biomedical Materials， 2018， 80：119-127.
［18］陈轲，云忠，周俊. TC4钛合金仿生骨植入体单元结构力学性能分析［J］. 机械科学与技术， 2020， 39（8）：1277-1282.
CHEN Ke， YUN Zhong， ZHOU Jun. Analysis of Mechanical Properties of TC4 Titanium Alloy Bionic Bone Implant Unit［J］. Mechanical Science and Technology for Aerospace Engineering， 2020， 39（8）：1277-1282.
［19］AL-SAEDI D S J， MASOOD S H， FAIZAN-UR-RAB M， et al. Mechanical Properties and Energy Absorption Capability of Functionally Graded F2BCC Lattice Fabricated by SLM［J］. Materials & Design， 2018， 144：32-44.
［20］WANG H， SU M M， HAO H. Compressive Properties and Energy Absorption Behavior of Mg17Al12/Al Ordered Structure Composites［J］. Composites Part B：Engineering， 2021， 210：108688.

[1]	LI Yingchun, NIE Aonan, YANG Mingxuan, ZHU Dingkang, QIU Ming, YANG Gengsheng. Research on Thermal Characteristics of Auxiliary Bearing in AMBs and Friction Reduction Design [J]. China Mechanical Engineering, 2024, 35(04): 646-655.
[2]	NI Jing, CUI Zhi, HE Lihua, FU Xin, ZHU Zefei. State-of-the-Art of Cutting Technology and Applications of PTFE [J]. China Mechanical Engineering, 2024, 35(03): 498-514.
[3]	LIANG Yongbin, FU Guang, LIN Zhigui, HE Zhicheng, ZHANG Jialuo, CHEN Tao. Design of Lane Keeping Assist Systems Based on Improved Preview Control Model [J]. China Mechanical Engineering, 2024, 35(03): 548-558.
[4]	HUANG Wei, CHI Cheng. Analysis for Aero -elastic Characteristics of Prop-Rotor in Hover with a Swept Tip [J]. China Mechanical Engineering, 2024, 35(02): 191-200.
[5]	XU Zuolin, HUANG Chuanzhen, LIU Huanlian, LIU Dun. Coating Technology and Mechanism of Modified Diamond Powder by Surface Coating of WC Powders [J]. China Mechanical Engineering, 2024, 35(02): 208-214.
[6]	YUE Jianfeng, LONG Xinyu, HUANG Yunlong, GUO Jialong, LIU Wenji. On-line Identification of Narrow Gap P-GMAW Sidewall Fusion States Based on Arc Acoustic Signals [J]. China Mechanical Engineering, 2024, 35(02): 244-250，259.
[7]	DU Xu, CHANG Zexin, ZHENG Junqiang, REN Pengfei. A Real-time Tool Path Smoothing Algorithm Considering Joint Jerk Constraints [J]. China Mechanical Engineering, 2024, 35(02): 280-286.
[8]	SUN Yuxiang, CHEN Li, LONG Bo, WANG Yanping, LIU Shihua, JIA Kun. Intelligent Layout for Pipeline Supports of Nuclear Power Plant under Complex Load [J]. China Mechanical Engineering, 2024, 35(02): 317-323，336.
[9]	LI Mozhi, ZHU Wenfeng, WANG Shunchao. Roller Pose Compensation in Automotive Body Roll-hemming Forming Process with Adhesive for Dimensional Deviation [J]. China Mechanical Engineering, 2024, 35(02): 364-370.
[10]	WANG Weijun, YANG Guilin, DU Qinghao, CHEN Qingying, . Design of 3K Planetary Gear Reducers with No Backlash [J]. China Mechanical Engineering, 2024, 35(01): 36-44,55.
[11]	GAO Jin, CUI Haibing, FAN Tao, LI Ang, DU Zunfeng. A Structural Reliability Calculation Method Based on Adaptive Kriging Ensemble Model [J]. China Mechanical Engineering, 2024, 35(01): 83-92.
[12]	SUN Haitao, ZHAN Mei, FAN Xiaoguang, GUO Jing, HAN Chao, ZHANG Jun. Research Progresses and Prospects of Compression Molding of High-performance PBX [J]. China Mechanical Engineering, 2024, 35(01): 160-180.
[13]	ZHU Fuxian, QIU Gang, ZHU Xingmin, XU Xianyi, ZHOU Jinyu. Failure Mode and Progressive Damage Analyses of Carbon-glass Hybrid Composite Single Nail and Single Shear Bolted Joints [J]. China Mechanical Engineering, 2023, 34(23): 2781-2793.
[14]	HAO Zhuangzhuang, ZHANG Qingchun, HU Yunbo, GUO Yibin, WANG Donghua, LI Wanyou. Research on Influences of Tooth Friction and Geometric Eccentricity Errors on Mesh Stiffness of Profile Shifted Spur Gear Pairs [J]. China Mechanical Engineering, 2023, 34(23): 2812-2823.
[15]	YU Shubo, LIU Zhansheng, ZHAO Chen. Dynamics Simulation Data Driven Domain Adaptive Intelligent Fault Diagnosis [J]. China Mechanical Engineering, 2023, 34(23): 2832-2841.