磨料射流抛光中各工艺参数对材料去除率及抛光区形貌的影响

J4 ›› 2008, Vol. 19 ›› Issue (21): 0-2645.

• 制造系统 •

磨料射流抛光中各工艺参数对材料去除率及抛光区形貌的影响

李兆泽;李圣怡;戴一帆;彭小强

收稿日期:1900-01-01 修回日期:1900-01-01 出版日期:2008-11-10 发布日期:2008-11-10

Effects of Various Parameters on Material Removal Rate and the 
Footprint in Abrasive Jet Polishing Process

Li Zhaoze;Li Shengyi;Dai Yifan;Peng Xiaoqiang

Received:1900-01-01 Revised:1900-01-01 Online:2008-11-10 Published:2008-11-10

摘要/Abstract

摘要：

介绍了磨料射流抛光的工作原理，并从试验出发，针对射流抛光技术的主要工艺参数（入射角度、射流速度、入射距离、抛光液浓度和工作时间等）对抛光特性的影响进行了试验研究。分析了各工艺参数与抛光效率和抛光点形貌的影响关系，从而获得了最佳工艺参数。在此基础上，对一平面K9光学玻璃进行了抛光试验，抛光速率约为30nm/min，抛光区粗糙度小于2.5nm。研究结果为磨料射流抛光加工的进一步研究提供了一定的帮助。


关键词: 磨料射流；抛光；去除率；表面粗糙度

Abstract:

This paper firstly introduced the principles of abrasive jet polishing. Then some key influence parameters of jet polishing technology, such as incidence angle, jet speed, incidence distance, abrasive concentration and processing time were investigated based on experiments. The relationships among various parameters and polishing efficiency and the footprint in polishing region were analyzed. Optimized relation curve of every parameter was obtained. Based on these, a plane K9 optical sample was polished. The polishing rate is about 30nm/min, and the roughness of this polishing region is less than 2.5nm. The results lay an experimental foundation for the further research of abrasive jet polishing.

Key words: abrasive jet, polishing, removal rate, surface roughness

中图分类号:

TH161

李兆泽;李圣怡;戴一帆;彭小强;. 磨料射流抛光中各工艺参数对材料去除率及抛光区形貌的影响[J]. J4, 2008, 19(21): 0-2645.

Li Zhaoze;Li Shengyi;Dai Yifan;Peng Xiaoqiang. Effects of Various Parameters on Material Removal Rate and the 
Footprint in Abrasive Jet Polishing Process[J]. J4, 2008, 19(21): 0-2645.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/

http://www.cmemo.org.cn/CN/Y2008/V19/I21/0

[1]	陈荣莲;程维明;贺耀龙;胡志宏;. 重型凸轮磨削温度场的仿真与实验研究[J]. J4, 2009, 20(20): 0-2398.
[2]	唐进元;陈海锋;. 主轴回转误差的相对静止测量原理与方法[J]. J4, 2009, 20(17): 0-2021.
[3]	李济顺;;雷贤卿;薛玉君;段明德;. 基于坐标变换的圆柱度误差评定算法[J]. J4, 2009, 20(16): 0-1895.
[4]	闫嘉钰;杨建国;. 灰色GM(X,N)模型在数控机床热误差建模中的应用[J]. J4, 2009, 20(11): 0-1292.
[5]	王秀山;杨建国;余永昌;邹彩虹;. 双转台五轴数控机床热误差建模、检测及补偿实验研究[J]. J4, 2009, 20(04): 0-388.
[6]	吴昊;杨建国;张宏韬;郭前建;. 三轴数控铣床切削力引起的误差综合运动学建模[J]. J4, 2008, 19(16): 0-2015.
[7]	焦长君;李圣怡;解旭辉;周林;. 光学镜面离子束加工系统设计和分析[J]. J4, 2008, 19(10): 0-1139.
[8]	张学成;戴一帆;李圣怡;彭小强;. 磁射流抛光的射流稳定性分析[J]. J4, 2008, 19(8): 0-888,.
[9]	汪世益;;黄筱调;顾伯勤;钱森力. null[J]. J4, 2008, 19(2): 174-178.
[10]	郭前建;杨建国;李永祥;王秀山. 滚齿机热误差补偿技术研究[J]. J4, 2007, 18(23): 0-2812.

磨料射流抛光中各工艺参数对材料去除率及抛光区形貌的影响

Effects of Various Parameters on Material Removal Rate and the 
Footprint in Abrasive Jet Polishing Process

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 10

编辑推荐

Metrics

磨料射流抛光中各工艺参数对材料去除率及抛光区形貌的影响

Effects of Various Parameters on Material Removal Rate and the  Footprint in Abrasive Jet Polishing Process

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 10

编辑推荐

Metrics

Effects of Various Parameters on Material Removal Rate and the 
Footprint in Abrasive Jet Polishing Process